manualshive.com logo in svg

Funkwerk 800ATC-(200)-(200), Эксплуатация и установка

Поделиться
Скачать
Funkwerk 800ATC-(200)-(200) Скачать руководство пользователя страница 17

TRT800 / P/N 800ATC-(200)-(200)  

Operation and Installation 

 

 
 

17

Document-No: 03.2102.010.71e / Revision: 2.02

3.6 Equipment 

Connections 

3.6.1 Electrical 

Connections 

One 15 pin D-SUB miniature connector includes all electrical 
connections, except for the antenna. Use only an AC Address Adaptor 
TRT800EM or TRT800EMSS as they are part of the certification and 
include a memory with the stored ICAO 24bit Aircraft Address. 

3.6.1.1 Mutual Suppression 

Other equipment on board (e. g. DME) may transmit in the same 
frequency band as the transponder. 
If such a device is installed a suppression wiring shall be installed in 
order to protect the receiving parts of the different devices from in-band 
transmissions. 
Mutual suppression is a synchronous pulse that is sent to the other 
equipment to suppress transmission of a competing transmitter for the 
duration of the pulse train transmission. The transponder transmission 
may be suppressed by an external source and vice versa. 
To activate mutual suppression connect the SUPP_I/O signal to the 
according signals of the other equipment 

3.6.1.2 Ground Switch 

If a Ground-Switch is connected (and activated in the Setup), the 
transponder is enabled to distinguish between On-Ground and In-Flight. 
Condition. In On-Ground Condition the transponder automatically enters 
the Standby mode. 
In order to activate this function the signal „FLY-GND“ must be 
connected to a switch, which combines the signal with „GND“ in case the 
gear is weighted, or remains open in the other case. 
This option must additionally be activated in the Setup. For details on 
configuration please refer to section 4.2.1. 

 

The (+UB)-wire has to protected by circuit breaker (2 Amp.)!

Содержание 800ATC-(200)-(200)







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды