manualshive.com logo in svg

FunkTronic Major 4, Руководство пользователя

Поделиться
Скачать
FunkTronic Major 4 Скачать руководство пользователя страница 15

m4_eng(11.03.02)

- 15 -

Kompetent für Elektroniksysteme

Setup Mode

Setup Menu

The setup menu is selected by pressing the (F1) key and the (F4) key simultaneously for one second. 

Now the message <SET> is shown on the left display and the cursor ashes at the input digit of the 

right display. Now it is possible to call the different programs by entering a two digit number (see the 

following table). The input is terminated by pressing the (F4) key.

 

00 =  Reset Program

 

01 =  EEPROM 1 programming mode

 

02 =  EEPROM 2 programming mode

 

03 =  Time setting of built in real time clock

 

04 =  Printout of EEPROM registers EEPROM 1

 

05 =  Printout of EEPROM registers EEPROM 2

 

06 =  Software Version display

 

50 =  Service mode processor board

 

51 =  Service mode telephone interface

EEPROM 1 Programming Mode

After selecting the EEPROM 1 in the setup menu, the left display shows the message <Pas>, and 

the cursor ashes at the input digit of the right display. Now you have to enter your 5 digit password. 

Units leave the factory without password, so that you can immediately start with the programming. 

In this case or after you have entered your password, the left display shows the message <Adr>, 

and the cursor ashes at the input digit of the right display.

Now the register address to be newly coded has to be entered (see the following table). If, instead 

of a valid address, '222' is entered, all registers are programmed with default values. Immediately 

after complete input the left display shows the message <Cod>, and the actual coding is shown 

on the right display. Now that coding can be overwritten with new values. If the coding shall not be 

modied, you can skip the coding by pressing the (F3) key and select a new address. Generally, 

in setup mode you conrm the last input by pressing the (F4) key, and by pressing the (F3) key 

you go to the next step of the program.

 

All values from 0 ... 9 and A ... F

 

can be used for coding. Value F

 

is shown on the display as '-'. 

 

 

After  complete  coding  the  EEPROM  is  programmed  by  pressing  the  (F4)  key.  Now  the  Major 

4  shows  the  word  <donE>  on  the  right  display  for  half  a  second.  Then  the  left  display  shows 

the  message  <Adr>,  and  the  cursor  ashes  at  the  input  digit  of  the  right  display.  Now  the  next 

address can be entered.

If no further coding are requested, you have to quit the programming mode by pressing the (F3) 

key.  Now  the  Major  4  is  executing  a  warm  start;  during  this  warm  start  all  registers  are  read  in 

and the programming mode is terminated.

F1 F2 F3 F4

A 1 2
B 4

3

5 6

C 7 8 9
D E 0 F

Содержание Major 4
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды