function Innovation & Technology AS KNX MultiLight Скачать руководство пользователя страница 26

Страница: 26 / 36

function Innovation & Technology AS

- 26 -

Manual – KNX MultiLight Art.nr 44001

Doc.no. D-TS-ML-K-005-A

7.4

Object list

Table 6 - Object list for the switch actuator

Name

Description

Configuration

OBJ 023

Relay 1 - Switch

The switch object to open or close

the relay. The object works for

switch actuator, delay function and

staircase function (1=closed,

0=open).

1 bit

1.001
Flag: C - W -

BJ 024

Relay: Force
operation

The relay will be forced open or

closed by setting this object high

according to the ”Forced operation”

parameter setting (”Relay on” or

”Relay off”). This object has the

highest priority for operating the

relay.

1 bit
1.001
Flag: C - W -

OBJ 025

Relay: Disable
staircase function

Disables the staircase timer function

1 bit
1.001

C W - -

OBJ 025

Relay: Disable
delay function

Disables the ON/OFF delay function.

1 bit
1.001

C W - -

OBJ 026

Relay: Change
duration

Object for changing the timer value

for the Staircase function. The value

is stored until next program

download.

2 byte
9.010

C R W -

OBJ 027

Relay: Logic AND

The object works as a AND gate for

the relay output regardless of which

function is enabled. Forced

operation will override the AND

gate. This object has the initial

value of “1” after power-on.

1 bit
1.001
C - W -

OBJ 027

Relay: Logic OR

The object works as an OR gate for

the relay output regardless of which

function is enabled. Forced

operation will override the OR gate.

This object has the initial value of

“0” after power-on.

1 bit

1.001
C - W -

OBJ 028

Relay: Status
switch

Holds the status information about

the relay output (1=relay closed,

0=relay open)

1 bit
1.001

Flag:

C R - T

Содержание KNX MultiLight





































Результаты поиска

Содержание KNX MultiLight

Отзывы:

Похожие инструкции для KNX MultiLight

Бренды по названию

Популярные бренды

function Innovation & Technology AS KNX MultiLight, Руководство пользователя

Результаты поиска

Содержание KNX MultiLight

Отзывы:

Похожие инструкции для KNX MultiLight

Бренды по названию

Популярные бренды