background image

 

unit remains on, but the image display is turned off by pressing the 
Power Button just momentarily. The red LED power indicator (15) 
will remain lit during the standby mode.  Always replace the 
objective lens cover after the unit is turned off and is no longer is in 
use. 

FOCUSING THE UNIT: 

To obtain the sharp image, you must rotate the Distance Focusing 
Knob (3) in either direction, until the image is at its best.  You may 
have to repeat the process again, until the image is sharp and clear.   

 

 

SUPER CONTROLLER FUNCTIONS: 

Your thermal device comes with a unique Super Controller (8), which 
allows for nearly instant image adjustment to the best possible 
brightness and clarity without having to enter the menu settings. This 
feature is extremely useful when atmospheric conditions change 
rapidly, especially during high humidity and/or rapid temperature 
changes. 

 

The super controller has the following sequence when short-pressed: 

1.  IMAGE GAIN (

GAIN

)  

2.  DISPLAY BRIGHTNESS (

BRGT

)       

3.  SENSITIVITY  (

SENS

)            

4.  IMAGE DETAIL ENHANCEMENT (

IDE

 

 

To adjust the IMAGE GAIN

, rotate the Super Controller either 

clockwise or counterclockwise while viewing the image 

– you will 

see word 

GAIN

 and either positive or negative number appear on 

the bottom left corner of the image display.  There are 10 negative 
and 10 positive Gain levels and a Zero level. Lowering the Image 
Gain will allow for better facial and detail recognition.  Increasing 
the Image Gain will allow for better target detection and 
recognition of surroundings, such as houses/buildings, trees and 
bushes and so on, allowing you to better see the target 
surroundings and to better orient in the terrain. 

 

To adjust the Display Brightness level

 short-press the 

Super Controller once and letters 

BRGT

 will appear in the display 

– you can now rotate the same switch and Display Brightness will 
change.  There are 30 levels of display brightness. During 
nighttime use, brightness level is optimal between 10 and 20, 
depending on the ambient conditions.  Keep in mind that higher 
brightness levels drain the batteries faster. 

 

To adjust the Thermal Sensitivity (

Sensor’s Brightness 

Output)

 short-press the GAIN switch twice and letters 

SENS

 will 

appear in the display 

– you can now rotate the same switch and 

Sensitivity will change.  There are 40 levels of sensitivity (min 
sensitivity is 40 and max is 80) 

Содержание O-40

















Отзывы: