Full Boar FBT-1100 Скачать руководство пользователя страница 12

Страница: 12 / 14

TROUBLESHOOTING

DESCRIPTION OF SYMBOLS

Warning

Read instruction manual

Wear eye protection

Double insulated

min

-1

Revolutions or

reciprocation per minute

No load speed

Volts

Hertz

Alternating current

Watts

Diameter

Regulator compliance mark

Wear ear protection

Millimetres

Symptom

Solution

Accessory is falling out

Accessory is jammed/ stuck
in concrete during use

Accessory repeatedly
becomes stuck while in use

Free the accessory as described above.
Refrain from penetrating too deeply with the
chisel bit, as it is prone to becoming stuck
when demolishing large pieces of concrete

The side handle is rotating

while in use.

Ensure the handle locking knob it tight by

rotating clockwise.

Ensure that the accessory is pushed in as far as

possible and the locking sleeve is released.

Pull the accessory locking sleeve back and

separate the accessory from the tool. The

accessory should be easily removed from

concrete once it is detached from the

demolition hammer.

Содержание FBT-1100















Результаты поиска

Содержание FBT-1100

Отзывы:

Похожие инструкции для FBT-1100

Бренды по названию

Популярные бренды

Full Boar FBT-1100, Инструкция по эксплуатации

Результаты поиска

Содержание FBT-1100

Отзывы:

Похожие инструкции для FBT-1100

Бренды по названию

Популярные бренды