Full Boar FBAST-100 Скачать руководство пользователя страница 17

Страница: 17 / 28

OPERATION (cont.)

View a summary of the system status (MIL

status, DTC counts, Monitor status) on the

TFT colour screen (1) (fig. 13).

Press any button for Diagnostic Menu. If

more than one module is detected, you

will prompted to select a module before

testing.

Use the Scroll button (7) to select a control

module and press Enter/Exit button (5) to

confirm (fig. 14).

Diagnostic menu - Read codes:

Reading Codes can be done with the ignition

on engine off or with the engine running. Stored Codes are also known as

“hard codes” or “permanent codes”. These codes cause the control module to

illuminate the malfunction indicator light (MIL) when emission-related fault occurs.

Pending Codes are also referred to as “maturing codes” or “continuous monitor

codes”. They indicate problems that the control module has detected during the

current or last driving cycle but are not considered serious yet. Pending Codes will

not turn on the malfunction indicator lamp (MIL). If the fault does not occur within

a certain number of warm-up cycles, the code clears from memory.

Use the Scroll button (7) to select Read

Codes and press Enter/Exit button (5) to

confirm (fig. 15).

OBD/EOBD

Ready Test

Setup

About

CHECK

Monitor Status

MIL status
Codes found
Monitors N/A
Monitors OK
Monitors INC

Control Module

1/2

Engine

A/T

OFF
6
3
3
5

Diagnostic Menu

1/7

Read Codes

Erase Codes
View Freeze Frame
I/M Readiness
Vehicle Information

Read Codes

1/3

Stored Codes

Pending Codes
Permanent Codes
Previous Menu

Stored Codes

1/3

P0115

1/3

Engine Coolant Temperature Sensor 1
Circuit

Diagnostic Menu

1/7

Read Codes

Erase Codes

View Freeze Frame
I/M Readiness
Vehicle Information

Erase Codes

Read Codes

Erase trouble codes!

Are you sure?

YES

Erase Codes

Erase done!

Press any button to con.

Erase Codes

Erase Failure.

Turn key on with Engine Off!

Press any button to con.

Fig. 13

OBD/EOBD

Ready Test

Setup

About

CHECK

Monitor Status

MIL status
Codes found
Monitors N/A
Monitors OK
Monitors INC

Control Module

1/2

Engine

A/T

OFF
6
3
3
5

Diagnostic Menu

1/7

Read Codes

Erase Codes
View Freeze Frame
I/M Readiness
Vehicle Information

Read Codes

1/3

Stored Codes

Pending Codes
Permanent Codes
Previous Menu

Stored Codes

1/3

P0115

1/3

Engine Coolant Temperature Sensor 1
Circuit

Diagnostic Menu

1/7

Read Codes

Erase Codes

View Freeze Frame
I/M Readiness
Vehicle Information

Erase Codes

Read Codes

Erase trouble codes!

Are you sure?

YES

Erase Codes

Erase done!

Press any button to con.

Erase Codes

Erase Failure.

Turn key on with Engine Off!

Press any button to con.

Fig. 14

OBD/EOBD

Ready Test

Setup

About

CHECK

Monitor Status

MIL status
Codes found
Monitors N/A
Monitors OK
Monitors INC

Control Module

1/2

Engine

A/T

OFF
6
3
3
5

Diagnostic Menu

1/7

Read Codes

Erase Codes
View Freeze Frame
I/M Readiness
Vehicle Information

Read Codes

1/3

Stored Codes

Pending Codes
Permanent Codes
Previous Menu

Stored Codes

1/3

P0115

1/3

Engine Coolant Temperature Sensor 1
Circuit

Diagnostic Menu

1/7

Read Codes

Erase Codes

View Freeze Frame
I/M Readiness
Vehicle Information

Erase Codes

Read Codes

Erase trouble codes!

Are you sure?

YES

Erase Codes

Erase done!

Press any button to con.

Erase Codes

Erase Failure.

Turn key on with Engine Off!

Press any button to con.

Fig. 15

Содержание FBAST-100





























Результаты поиска

Содержание FBAST-100

Отзывы:

Бренды по названию

Популярные бренды

Full Boar FBAST-100, Инструкция по эксплуатации

Результаты поиска

Содержание FBAST-100

Отзывы:

Бренды по названию

Популярные бренды