FULGOR F7PBM36S1-R, Руководство по установке

Страница: 8 / 60

15 14
EN EN
2.6 Installation cutout features:
Stainless exterior Pro
(European standard cutout width)
A
Minimum cutout height
2134 mm (84”)
Minimum cutout width
36” model: 900 mm (35 1/2”)
30” model: 750 mm (29 5/8”)
24” model: 600 mm (23 3/4”)
Depth with door
635 mm (25 ”)
Area to be left clear for the anti-tipping brackets
127 mm (5”) for both right and left sides
B
Appliance height
2120 mm (83 1/2”) + 25 mm (1”)
If the units are to be installed inside
a cutout or within an enclosed
structure, it is necessary to design
a ventilation shaft at the back of the
cutout to assure proper ventilation at
the back of the unit.
Cross-sectional chimney ventilation
area should equal 200cm² (31in²).
Door Swing Clearance
Minimum distance from
the wall (hinge side)
2. TECHNICAL REQUIREMENTS
A A
140 (5 ½”) 140 (5 ½”)
36”: 900 mm (35 ½”)
24”: 600 mm (23 ¾”)
30”: 750 mm (29 ⅝”)
560 (22”)
635 (25”)
693 (27 ¼”)
195 (7 ⅝”)
8 (⅜”)
8 (⅜”)
97 (3 ⅞”)
+ 25 (1”)
100 (4”) 100 (4”)
min 2134
(84”)
2120 (83 ½”)
+25 (1”)
613 (24 ⅛”)
+25 (1”)
1296
(50”)
516
(20 ⅜”)
B
A
A A
140 (5 ½”) 140 (5 ½”)
36”: 900 mm (35 ½”)
24”: 600 mm (23 ¾”)
30”: 750 mm (29 ⅝”)
560 (22”)
635 (25”)
693 (27 ¼”)
195 (7 ⅝”)
8 (⅜”)
8 (⅜”)
97 (3 ⅞”)
+ 25 (1”)
100 (4”) 100 (4”)
min 2134
(84”)
2120 (83 ½”)
+25 (1”)
613 (24 ⅛”)
+25 (1”)
1296
(50”)
516
(20 ⅜”)
min 10 (⅜”)
36" model : 899 ( 35 ⅜ ”)
30" model: 749 (29 ½ ”)
24" model : 599 ( 23 ⅝ ”)
100°
36" model: 230 (9”)
30" model: 195 (7 ¾”)
24" model: 160 (6 ¼”)
36" model: 1470 (57 ⅞”)
30" model: 1320 (52”)
24" model: 1170 (46”)
1016 (40”)
635 (25”)
560 (22”)
75 (3”)
10 (⅜”)
58 (2 ¼”)
36" model : 899 ( 35 ⅜ ”)
30" model: 749 (29 ½ ”)
24" model : 599 ( 23 ⅝ ”)
100°
36" model: 230 (9”)
30" model: 195 (7 ¾”)
24" model: 160 (6 ¼”)
36" model: 1470 (57 ⅞”)
30" model: 1320 (52”)
24" model: 1170 (46”)
1016 (40”)
635 (25”)
560 (22”)
75 (3”)
10 (⅜”)
58 (2 ¼”)
When installing
our top
compressor
models in a new
construction, it is
recommended to
use the European
“cutout”
dimensions
to achieve a
minimal gap on
the lateral sides
and avoid the
need to use the
J-profile trim kit.
Installing in the
unit in a standard
North American
“cutout” without
the J-profile trim
kit, will result
in a larger gap
along the cabinet
opening.