1-2
SPARC Enterprise M4000/M5000 Servers Service Manual • December 2010
Caution –
Attach the cord of the antistatic wrist strap directly to the server. Do not
attach the antistatic wrist strap to the ESD mat connection.
The antistatic wrist strap and any components you remove must be at the same
potential.
1.2
System Precautions
For your protection, observe the following safety precautions when servicing your
equipment:
■
Follow all cautions, warnings, and instructions marked on the equipment.
■
Never push objects of any kind through openings in the equipment, as they might
touch dangerous voltage points or short out components that could result in fire
or electric shock.
■
Refer servicing of equipment to qualified personnel.
1.2.1
Electrical Safety Precautions
Ensure that the voltage and frequency of the power outlet to be used match the
electrical rating labels on the equipment.
Wear antistatic wrist straps when handling any magnetic storage devices,
system boards, or other printed circuit boards.
Use only properly grounded power outlets as described in the
SPARC Enterprise
M4000/M5000 Servers Installation Guide
.
Caution –
Do not
make mechanical or electrical modifications. The manufacturer is
not responsible for regulatory compliance of modified servers.
1.2.2
Equipment Rack Safety Precautions
All equipment racks should be anchored to the floor, ceiling, or to adjacent frames,
using the manufacturer’s instructions.
Содержание SPARC Enterprise M4000
