Fujitsu SCENIC6511 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 57

background image

System expansions

A26361-K520-Z100-1-7619

37

Changing the floppy disk drive

Open the system unit (see "

Opening the system unit

").

Remove the hard disk carrier (see "

Installing and removing the hard disk drive

").

1

2

Pull the data and the power supply
connectors from the floppy disk drive.

Remove the screw (1) and take the drive
out of the system unit (2).

Take the new floppy disk drive out of its
packaging.

2

1

Push the drive into the system unit (1), and
fix it with the screw (2).

Plug the data and the power supply
connectors into the floppy disk drive.

Remove the hard disk carrier (see
"

Installing and removing the hard disk

drive

").

Close the system unit (see "

the system unit

").

i

If necessary, you must adapt the entry for the drive in the Setup menu.

«
...
35
36
37
38
39
...
»

Содержание SCENIC6511


























































Отзывы:

Нет отзывов

Похожие инструкции для SCENIC6511

Бренд: IBM Страницы: 170

Бренд: IBM Страницы: 257

Бренд: IBM Страницы: 63

Бренд: Gateway Страницы: 124

Бренд: Quanmax Страницы: 63

Бренд: Kontron Страницы: 68

Бренд: Atari Страницы: 16

Бренд: E-Medic Страницы: 31

BRIX GB-BACE-3150

Бренд: Gigabyte Страницы: 2

Бренд: Dell Страницы: 70

Бренд: HP Страницы: 122

Apollo 9000 400dl

Бренд: HP Страницы: 296

9000 Model D280

Бренд: HP Страницы: 68

A1210n - Pavilion - 512 MB RAM

Бренд: HP Страницы: 120

6200 Pro Series Microtower

Бренд: HP Страницы: 345

Бренд: HP Страницы: 33

6735b - Notebook PC

Бренд: HP Страницы: 34

Бренд: HP Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды