Fujitsu Primergy BX2560 M1 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 68

background image

BX2560 M1

Operating Manual

15

Functional overview

Hard disk drives (HDD) / Solid state drives (SSD)

The server blade can be equipped with a maximum of two 2.5-inch HDD/SSD
modules.

Each HDD/SSD module can accommodate an SAS/SATA hard disk drive or an
SAS/SATA SSD drive. The module is connected to the HDD backplane
wirelessly. This allows HDD/SSD modules to be plugged in or pulled out easily.

Two SAS/SATA hard disk drives or SAS/SATA SSD drives can be controlled by
the onboard SATA controller or the SAS/SATA RAID controller.

Mixed configurations of SAS HDDs, SATA HDDs, SAS SSDs and SATA SSDs
within the same logical drive (RAID array) are not supported.

If the server blade has a corresponding RAID configuration, HDD/SSD modules
can also be replaced during operation.

Onboard CNA controller

A CNA controller is integrated on the system board; up to 4 x 1 Gbit/s or
2x 10 Gbit/s can be selected on the CNA controller.

For more information on configuring the controller, see section

"Configuring the

onboard CNA controller" on page 59

.

Onboard SATA controller

A SATA controller is integrated on the system board; up to two SATA hard disk
drives or SATA SSD drives can be connected to the controller. The LSI
Embedded MegaRAID software (SATA Software RAID) supports RAID levels 0
and 1.

For more information on configuring the controller, see section

"Configuring the

onboard SATA controller" on page 58

.

«
...
13
14
15
16
17
...
»

Содержание Primergy BX2560 M1





































































Отзывы:

Нет отзывов

Похожие инструкции для Primergy BX2560 M1

Бренд: US Robotics Страницы: 156

Бренд: Shenzhen JingFeng Страницы: 11

Бренд: LevelOne Страницы: 88

BocaVision WT120

Бренд: Boca Systems Страницы: 28

Бренд: LG Страницы: 100

Бренд: LG Страницы: 35

IC125-FASTPOCKET-FX

Бренд: SEH Страницы: 20

Бренд: SEH Страницы: 32

Бренд: Bosanova Страницы: 2

Бренд: Bosanova Страницы: 2

Бренд: Compatible Systems Страницы: 75

PD02 PCoIP Zero Client

Бренд: EVGA Страницы: 2

PD02 PCoIP Zero Client TAA Compliant

Бренд: EVGA Страницы: 2

Бренд: Inspur Страницы: 2

Бренд: RFL Electronics Страницы: 20

Dual Processor AS 1020C-3

Бренд: Supero Страницы: 106

Бренд: Xiva Страницы: 41

STRATOS S210 Series S210-X22RQ

Бренд: QUANTA Страницы: 252

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды