Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 98

Страница: 98 / 344

Remark

The IP address of the LAN cannot be set through the operating system setup. Set the IP address after the

installation of the operating system.

7. Click [Install].

Installation begins.

8. Replace the media with the operating system installation media according to the SVIM instructions.

4.3.4

Configuring bundled software after the completion of installation

After completing OS installation, configure the bundled software.

1. Confirm that the PSA management LAN IP address is not the same as the IP address used for the production

network or management network. For details in the case of the PRIMEQUEST 1800E2, see the

ServerView

Mission Critical Option User Manual

. For details in the case of the PRIMEQUEST 1800E, see

6.2.1

Configuring the PSA-to-MMB communication LAN

Remarks

The PSA management LAN is automatically assigned an IP address. Confirm that the IP address is not the

same as the IP address used for the production network or management network. If the IP addresses match,

change the PSA management LAN IP address. Also, if the subnets match, change the subnet setting on the

MMB side.

2. Configure and confirm the management LAN.

- Configuring the management LAN used for communication with the MMB

(See

6.2.2 Confirming management LAN settings

If necessary, configure any duplication with bonding or PRIMECLUSTER GLS, for example.

- Confirming SELinux function settings

(See

6.2.3 Confirming SELinux function settings

Confirm that the SELinux function is [disabled].

3. Check the firewall function. For details, see

6.2.4 Checking the firewall function (opening ports)

- Open the ports for the PSA-to-MMB communication LAN interfaces.

snmp port: udp/snmp or 161

web-mmb communication port: tcp/fj-webgate or 24450

psa-mmb communication port: tcp/5000 on the MMB side

icmp: echo-request

icmp: echo-reply

4. Set the destinations of SNMP trap from the partition.

Set the destinations of traps and PSA trap notification on the partition side as needed. For details, see

6.2.5

Setting the destinations of traps from a partition

Remarks

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 4 Installing the Operating System and Bundled Software

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды