Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 123

Страница: 123 / 344

4.7.3

Installing VMware 4.x

Install VMware 4.x by following the instructions in the

VMware vSphere Software Handbook

For details on this handbook, contract your sales representative.

Before starting installation, see

E.2 Notes on VMware 4.x Installation

4.7.4

Installing bundled software

After completing installation of the operating system, configure the bundled software.

- Installing ServerView Agent

(See

E.3.1 Installing ServerView Agent

- Installing ServerView RAID

(See

E.3.2 Installing ServerView RAID

- Installing RAS Support Service

(See

E.3.3 Installing RAS Support Service (PRIMEQUEST)

- Installing HRM/server

(See

E.3.4 Installing VMware 4.x HRM/server (PRIMEQUEST)

- Installing PSA (1800E)

(See

E.3.5 Installing VMware 4.x PSA

- Installing SVmco (1800E2)

(See the

ServerView Mission Critical Option User Manual

)

4.7.5

Configuring bundled software

Configure the bundled software. For details on confirming and configuring the LAN, see

E.4.1 Configuring the

network

1. Confirm the PSA-to-MMB communication LAN and management LAN.

The PSA-to-MMB communication LAN uses the physical adapter assigned BUS number 0000:00:19.0. The

management LAN uses an arbitrary physical adapter.

Execute the esxcfg-nics command to confirm the physical adapters used for the PSA-to-MMB

communication LAN and management LAN.

2. Configure the management LAN.

1. Use vswif0, which exists by default immediately after the installation of the operating system, for the

interface of the management LAN.

2. Execute the esxcfg-vswif command to assign an IP address to vswif0.

3. Configure the PSA-to-MMB communication LAN.

1. Execute the esxcfg-vswitch command to create a virtual switch (vSwitch1).

2. Execute the esxcfg-vswitch command to connect physical adapter vmnic0 to the virtual switch.

3. Add a port group (PSA-MMB) to the created switch.

4. Execute the esxcfg-vswif command to create a virtual port (vswif1).

5. Add the following settings to the PSA-to-MMB communication LAN:

Speed: 100 Mbps

Duplex: full

6. Set the IP address of the PSA-to-MMB communication LAN in the PSA configuration file.

4. Configure the firewall. For details, see

E.4.2 Configuring the firewall

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 4 Installing the Operating System and Bundled Software

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды