Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 293

Страница: 293 / 344

E.3

Installing VMware 4.x Bundled Software

The bundled software is stored in ServerView Suite DVD1. Copy the files from ServerView SuiteDVD1 and use

them.

E.3.1

Installing ServerView Agent

Install ServerView Agent by referring to the following manuals:

- ServerView Suite

ServerView Operations Manager V4.92

Installation ServerView Agents for Linux

Installation ServerView Agents (SuSE, Red Hat and VMware 4.x)

Installation ServerView Update Agent

Note the following points during the installation.

- Even if ServerView Suite DVD1 is inserted into the drive, the media is not mounted automatically. Execute

the mount command.

# mount -t udf /dev/cdrom /MNT

* MNT is the mount point.

- Use the files for V4.92, which are stored in the following directory:

/MNT/SVSSoftware/Software/ServerView/Linux/Agents_V492

* MNT is the mount point.

E.3.2

Installing ServerView RAID

This section describes how to install ServerView RAID.

1. Start the terminal with root privileges.

2. Mount ServerView Suite DVD1.

3. Execute the following command.

# rpm -ivh /MNT/SVSSoftware \

/Software/ServerView/Linux/ServerView_RAID/\

ServerView_RAID-XXX.i686.rpm

* MNT is the mount point.

\: This indicates that there is no line feed.

XXX depends on the version or operating system distribution.

E.3.3

Installing RAS Support Service (PRIMEQUEST)

This section describes hot to install the RAS Support Service (PRIMEQUEST).

PRIMEQUEST 1000 Series Installation Manual
APPENDIX E Notes on VMware Installation

265

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды