Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 290

Страница: 290 / 344

E.2

Notes on VMware 4.x Installation

Install VMware 4.x by following the instructions in the

VMware vSphere 4.x Software Handbook

For details on the VMware 4.x information and procedures that you need to know for PRIMEQUEST system

configuration, contact the distributor where you purchased your product, or your sales representative.

Note the following points during VMware 4.x installation.

- To make the network settings for the PRIMEQUEST 1800E, use the steps in

E.4 Settings after VMware 4.x

PSA Installation

- After completing the installation, press the [Alt] + [F1] keys to log in to the ESX Console.

FIGURE E.1 Completion of VMware 4.x installation

- When VMware 4.x is used, fatal system errors such as a panic are not detected automatically.

Therefore, perform the following procedures after installation and set the Watchdog Timer for detecting such

fatal system errors.

For setting the Watchdog Timer monitoring, use ServerView Operations Manager (V4.92-14 or later).

Note

The setting procedure varies with the version of ServerView Operations Manager (SVOM) being used. Check

the version number, and follow the appropriate procedure below.

When using SVOM 4.92

1. Start ServerView Operations Manager.

2. Select [ServerList].

3. Right-click the target partition in the server list on the left side. Select [Maintenance] - [ASR Properties] from

the displayed menu.

4. Select [Watchdog] in the displayed window.

5. Specify the following for [Software], and click [Apply].

- Check the [Active] check box.

- Select [Continue] for [Action] for cases of abnormal operation.

PRIMEQUEST 1000 Series Installation Manual
APPENDIX E Notes on VMware Installation

262

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды