Fujitsu Plasmavision PDS4229W-B Скачать руководство пользователя страница 10

Страница: 10 / 44

– 13 –

TROUBLESHOOTING FLOWCHART

LED lamp blinking

Turn power on and check
state of lamp.

Not lighted.

LAMP STATE

Power supply
circuit faulty.

POWER SUPPLY STATE

∗

Replace Main
Power PCB.

REMEDY

∗

Vs and -Vy must be adjusted.

Blinks
continuously.

Power turned off
immediately.

RED

Check 1

Blinks continuously.

Power turned off
immediately.

RED

Check 1

Blinks once

Power turned off
after 10 sec.

RED

Check 2

Blinks twice

Power turned off
after 10 sec.

RED

Check 3

Blinks four times

Power not turned
off, LED blinks only.

RED

Replace Main/Digital
PCB Assy.

Blinks five times

Power not turned
off, LED blinks only.

RED

Replace Video PCB
Assy.

Is on-screen display
normal?

Check 4

All input image
faulty.

Signal processing
PCB faulty.

Replace Main/Digital
PCB Assy.

Video input image
faulty.

Check 5

S-video input image
faulty.

Check 5

Component video
input image faulty.

Check 6

RGB input image
faulty.

Check 7

Lights steadily for
more than 10 sec.

GREEN

YES

Note : 1. Since a voltage is applied to the Main Power

PCB and PFC PCB heat sinks while the set is
operating, do not touch the heat sinks.

2. If the PFC PCB insulation sheet is not

installed when assembling, the PFC PCB
fuse will blow.

3. After the power cord plug was pulled out, do

not pull out the connector on the Main Power
PCB until the green LED(D531) turns off.

Содержание Plasmavision PDS4229W-B













































Результаты поиска

Содержание Plasmavision PDS4229W-B

Отзывы:

Похожие инструкции для Plasmavision PDS4229W-B

Бренды по названию

Популярные бренды

Fujitsu Plasmavision PDS4229W-B, Руководство по обслуживанию

Результаты поиска

Содержание Plasmavision PDS4229W-B

Отзывы:

Похожие инструкции для Plasmavision PDS4229W-B

Бренды по названию

Популярные бренды