manualshive.com logo in svg

Fujitsu M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf, Руководство оператора

Поделиться
Скачать
Fujitsu M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf Скачать руководство пользователя страница 33

 2-4

Repositioning the Shipping Lock

To keep the scanner from being damaged during shipping, the carrier unit is fixed with a Shipping
Lock. After placing the carrier unit where it will be installed, change the position of this Shipping Lock
as explained below.

1 Place the image scanner on the edge of the desktop so that the left side of the scanner (where

the ADF is attached) extends from the desktop. Do not set the image scanner upside down or
on its side.

  

CAUTION

Do not let the scanner hang more than 20 cm (8 in.) over the edge of the desk.

2 Remove the shipping lock from position  A . Then, install the shipping lock at position  B .

  

CAUTION

Before moving or storing the scanner, make sure that the shipping lock is set to the
shipment position to prevent possible damage.  Before setting the shipping lock, make sure
that the carrier has been returned to the home position.

B

A

Good

Bad

Bad

less than 20 cm

(8 in.)

Front side

Front side

Enlarged

Shipping Lock
(Position for operation)

Shipping Lock
(Position for shipment)

ADF side

Bottom view
Shipping Lock
(Position for storage,
position for shipment)
Enlarged section A

Содержание M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды