Fujitsu M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf Скачать руководство пользователя страница 101

Страница: 101 / 116

7-18

6 At Screen 58-3, designate the page edge

filter area through or button.

7 Press to declease or to increase the

value.
The increment/decrement is 1mm and the
value can be selected from 0 through 15.
Then, press to display Screen 58-4.

NOTICE

When a plus figure is designated, the area is set upward from the bottom edge of the image.
When a minus figure is designated, the area is set downward from the bottom edge of the image.
The standard value is the paper 3mm.

8 At Screen 58-4, designate the page edge

filter area through or button.

9 Press to declease or to increase the

value.
The increment/decrement is 1mm and the
value can be selected from 0 through 15.
Then, press to display Screen 58-5.

NOTICE

The page edge filter area from the left edge towards the right is in proportion to the above set value.

Содержание M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf





















































































































Результаты поиска

Содержание M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf, Руководство оператора

Результаты поиска

Содержание M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf

Отзывы:

Бренды по названию

Популярные бренды