Fujitsu ETERNUS AF S3 Series страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 204

background image

2. Basic Functions

This chapter describes the functions that control the storage system.

RAID Functions

This section explains the points to note before configuring a system using the ETERNUS AF.

Supported RAID

The ETERNUS AF supports the following RAID levels.

•

RAID0 (striping)

•

RAID1 (mirroring)

•

RAID1+0 (striping of pairs of mirrored drives)

•

RAID5 (striping with distributed parity)

•

RAID5+0 (double striping with distributed parity)

•

RAID6 (striping with double distributed parity)

•

RAID6-FR (striping with double distributed parity which provides high-speed rebuild capabilities)

IMPORTANT

Remember that a RAID0 configuration is not redundant. This means that if a RAID0 drive fails, the data
will not be recoverable.

This section explains the concepts and purposes (RAID level selection criteria) of the supported RAID levels.

■

RAID Level Concept

A description of each RAID level is shown below.

●

RAID0 (Striping)
Data is divided into blocks and allocated across multiple drives.

●

RAID1 (Mirroring)
The data is stored on two duplicated drives at the same time.
If one drive fails, the other drive continues operation.

●

RAID1+0 (Striping of Pairs of Mirrored Drives)
RAID1+0 combines the high I/O performance of RAID0 (striping) with the reliability of RAID1 (mirroring).

●

RAID5 (Striping with Distributed Parity)
Data is divided into blocks and allocated across multiple drives together with parity information created
from the data in order to ensure the redundancy of the data.

●

RAID5+0 (Double Striping with Distributed Parity)
Multiple RAID5 volumes are RAID0 striped. For large capacity configurations, RAID5+0 provides better
performance, better reliability, and shorter rebuilding times than RAID5.

●

RAID6 (Striping with Double Distributed Parity)
Allocating two different parities on different drives (double parity) makes it possible to recover from up to
two drive failures.

22

Design Guide

«
...
20
21
22
23
24
...
»

Содержание ETERNUS AF S3 Series













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETERNUS AF S3 Series

Taylor-Wharton XL-65

Бренд: Harsco Страницы: 26

Бренд: FAST LTA Страницы: 8

EonServ 5000 Series

Бренд: Surveon Страницы: 33

GHESS 9.8-14.4-TH

Бренд: GMDE Страницы: 50

Бренд: Swissbit Страницы: 11

Power 7 Wi-Fi SD/USB Storage kit

Бренд: Ravpower Страницы: 60

Бренд: U.S. General Страницы: 2

Бренд: Seville Classics Страницы: 7

Бренд: Beta Страницы: 7

Бренд: NEC Страницы: 4

Бренд: NEC Страницы: 8

Бренд: NEC Страницы: 12

Бренд: NEC Страницы: 48

Бренд: NEC Страницы: 53

Бренд: NEC Страницы: 106

Бренд: NEC Страницы: 118

Бренд: NEC Страницы: 120

Бренд: NEC Страницы: 168

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды