Fujitsu ASHA18GBCH, Руководство по эксплуатации

Страница: 4 / 8

En-3
2. Remove dust with a vacuum cleaner or by washing.
After washing, allow to dry thoroughly in a shaded place.
3. Replace the Air Filter and close the Intake Grille.
(1) Align the sides of the air filter with the panel, and push in fully, making
sure the two lower tabs are returned properly to their holes in the panel.
Hooks
(two places)
(2) Close the Intake Grille.
(For purposes of example, the illustration shows the unit without
Intake Grille installed.)
● Dust can be cleaned from the air filter either with a vacuum cleaner,
or by washing the filter in a solution of mild detergent and warm water.
If you wash the filter, be sure to allow it to dry thoroughly in a shady
place before reinstalling.
● If dirt is allowed to accumulate on the air filter, airflow will be reduced,
lowering operating efficiency and increasing noise.
● During periods of normal use, the Air Filters should be cleaned every
two weeks.
● When used for extended periods, the unit may accumulate dirt
inside, reducing its performance. We recommend that the unit be
inspected regularly, in addition to your own cleaning and care. For
more information, consult authorized service personnel.
●When shutting down the unit for one month or more, first allow the
fan mode to operate continuously for about one-half day to allow
internal parts to dry thoroughly.
Air Cleaning Filter Installation
1. Open the Intake Grille and remove the Air filters.
Air Filter (Right & Left)
2. Install the Air cleaning filter set (set of 2).
(1) Set the air cleaning filter into the air cleaning filter frame.
Air cleaning filter set
Air cleaning filter frame
Air cleaning filter
(2) Engage the latch at both ends of the filter with the two hooks at the rear
of the air cleaning filter frame.
Hook (2 places at the rear)
Latch (2 places)
Take care that the air cleaning filter does not project beyond the frame.
(3) Engage the four fixing locations at the top and bottom of the air cleaning
filter frame with the hooks of the air filter.
Rear of the filter
Fixing location, hook (6 places)
CLEANING AND CARE
CAUTION
● Before cleaning the unit, be sure to stop the unit and disconnect the
power supply.
● Be sure the Intake Grille is installed securely.
● When removing and replacing the air filters, be sure not to touch the
heat exchanger, as personal injury may result.
● Do not clean the inside of the unit by yourself. To clean the inside,
always consult authorized service personnel.
● When cleaning the unit’ body, do not use water hotter than 40 °C,
harsh abrasive cleansers, or volatile agents like benzene or thinner.
● Do not expose the unit body to liquid insecticides or hair sprays.
Cleaning the Intake Grille
1. Remove the Intake Grille.
(1) Place your fingers at both lower ends of the grille panel, and lift
forward; if the grille seems to catch partway through its movement,
continue lifting upward to remove.
(2) Pull past the intermediate catch and open the Intake Grille wide so
that it become horizontal..
(1)
(1)
(2)
(2)
Intake Grille
Mounting
shaft
Knob
2. Clean with water.
Remove dust with a vacuum cleaner; wipe the unit with warm water, then
dry with a clean, soft cloth.
3. Replace the Intake Grille.
(1) Pull the knobs all the way.
(2) Hold the grille horizontal and set the left and right mounting shafts into
the bearings at the top of the panel.
(3) Press the place where the arrow on the diagram indicates and close
the Intake Grille.
(1)
(2)
Mounting shaft
Knob
Intake
Grille
Bearing
Mounting shaft
Knob
Cleaning the Air Filter
1. Open the Intake Grille, and remove the air filter.
Lift up the air filter’s handle, disconnect the two lower tabs, and pull out.
Air filter handle
Hooks
(two places)
9377772299_OM.indb 3 30/01/2017 14:11:39