background image

En-16

7.4. Function setting

•  FUNCTION SETTING can be performed with the wired or wireless remote controller.
  (The remote controller is optional equipment)
•  Refer to the wired or wireless remote controller manual for detailed setting information. 
•  Refer to “7.1. Setting the address” for indoor unit address and refrigerant circuit address 

settings.

•  Turn the power of the indoor unit ON before starting the setting.

*  Turning on the power to the indoor units initializes EEV, so make sure the piping 

air tight test and vacuuming have been conducted before turning on the power.

*  Also check again to make sure no wiring mistakes were made before turning 

on the power.

Function details

Function

Function 

number

Setting number

Default

Details

Filter 
indicator 
interval

11

00

Standard

Adjust the 

fi

 lter cleaning 

interval noti

fi

 cation. If the 

noti

fi

 cation is too early, 

change to setting 01. If the 
noti

fi

 cation is too late, change 

to setting 02.

01

Longer

02

Shorter

Filter 
indicator 
action

13

00

Enable

Enable or disable the 

fi

 lter 

indicator. Setting 02 is for 
use with a central remote 
controller.

01

Disable

02

Display only 
on central 
remote con-
troller

Cool air 
temperature 
trigger

30

00

Standard

Adjust the cool air trigger 
temperature. To lower the 
trigger temperature, use 
setting 01. To raise the trigger 
temperature, use setting 02.

01

Adjust (1)

02

Adjust (2)

Heat air 
temperature 
trigger

31

00

Standard

Adjust the heat air trigger 
temperature. To lower the 
trigger temperature by 6 
degrees C, use setting 01. To 
lower the trigger temperature 
by 4 degrees C, use setting 
02. To raise the trigger tem-
perature, use setting 03.

01

Adjust (1)

02

Adjust (2)

03

Adjust (3)

Auto restart

40

00

Enable

Enable or disable automatic 
system restart after a power 
outage.

01

Disable

Cool Air 
Prevention

43

00

Super low

Restrain the cold air

fl

 ow 

with making the air

fl

 ow 

lower when starting heating 
operation. To correspond to 
the ventilation, set to 01.

01

Follow the 
setting on 
the remote 
controller

External 
control

46

00

Start/Stop

Allow an external controller to 
start or stop the system, or to 
perform an emergency stop.
*  If an emergency stop is 

performed from an external 
controller, all refrigerant 
systems will be disabled.

*  If forced stop is set, indoor 

unit stops by the input to 
the external input terminals, 
and Start/Stop by a remote 
controller is restricted.

01

Emergency 
stop

02

Forced stop

Error report 
target

47

00

All

Change the target for report-
ing errors. Errors can either 
be reported in all locations, 
or only on the central remote 
controller.

01

Display only 
on central 
remote 
controller

Fan set-
ting when 
cooling 
thermostat 
OFF

49

00

Follow the 
setting on 
the remote 
controller

When set to 01, the fan stops 
when the thermostat is OFF 
in cooling operation. Con-
nection of the wired remote 
controller (2-wire type or 
3-wire type) and switching its 
thermistor are necessary.

01

Stop

(Forbidden)

60

00

(Forbidden)

61

00

(Forbidden)

62

00

8. TEST RUN

8.1. Test run using Outdoor unit (PCB)

•  Refer to the Installation Manual for the outdoor unit if the PCB for the outdoor unit is to 

be used for the test run.

8.2. Test run using Remote Controller

•  Refer to the Installation Manual for the remote controller to perform the test run using 

the wireless remote controller.

•  When the air conditioner is being test run, the OPERATION and TIMER indicator lamps 

fl

 ash slowly at the same time.

For details, please refer to the Manual of “IR Receiver Unit” or “Wired Remote Controller”.

9. CHECK LIST

Pay special attention to the check items below when installing the indoor unit(s). After 
installation is complete, be sure to check the following check items again.

CHECK ITEMS

If not performed correctly

CHECK 

BOX

Has the indoor unit been installed 
correctly?

Vibration, noise,
indoor unit may drop

Has there been a check for gas leaks 
(refrigerant pipes)?

No cooling, No heating

Has heat insulation work been 
completed?

Water leakage

Does water drain easily from the indoor 
units?

Water leakage

Is the voltage of the power source the 
same as that indicated on the label on 
the indoor unit?

No operation, heat or burn 
damage

Are the wires and pipes all connected 
completely?

No operation, heat or burn 
damage

Is the indoor unit earthed (grounded)?

Short circuit

Is the connection cable the specified 
thickness?

No operation, heat or burn 
damage

Are the inlets and outlets free of any 
obstacles?

No cooling, No heating

Does start and stop air conditioner 
operation by remote controller 
or external device?

No operation

After installation is completed, has the 
proper operation and handling been 
explained to the user?

9373385202_IM.indb   Sec1:16

9373385202_IM.indb   Sec1:16

12/2/2015   9:56:06 AM

12/2/2015   9:56:06 AM

Содержание AirStage ARXA24GBLH



















Отзывы: