Fujitsu 8FX Скачать руководство пользователя страница 581 | Manualshive

Страница: 581 / 650

background image

MB95630H Series

MN702-00009-2v0-E

FUJITSU SEMICONDUCTOR LIMITED

559

CHAPTER 26 DUAL OPERATION FLASH MEMORY

26.6 Operations

26.6

Operations

Pay attention in particular to the following points when using dual operation
Flash memory:
• Interrupt generated when upper banks are updated
• Procedure of setting the sector swap enable bit in the flash memory status

register (FSR:SSEN)

■

Interrupt Generated When Upper Banks Are Updated

The dual operation Flash memory consists of two banks. Like conventional Flash products,

however, it cannot be erased/programmed and read at the same time in banks on the same side.

As SA2 contains an interrupt vector, an interrupt vector from the CPU cannot be read normally

when an interrupt occurs during programming data to an upper bank. Before an upper bank can

be updated, set the sector swap enable bit (FSR:SSEN) to "1". When an interrupt occurs,

therefore, SA1 is accessed to read interrupt vector data. Copy the same data to SA1 and SA2

before setting the FSR:SSEN bit.

■

Procedure for Setting Sector Swap Enable Bit (FSR:SSEN)

Figure 26.6-1 shows a sample procedure of setting the sector swap enable bit (FSR:SSEN).

To modify data in the upper bank, set FSR:SSEN to "1". While data is being written to the

Flash memory, modifying the setting of FSR:SSEN is prohibited. The setting of FSR:SSEN

can only be modified before the start of programming data to the Flash memory or after the

completion of programming data to the Flash memory. In addition, control the Flash memory

interrupts while setting FSR:SSEN as follows: before setting FSR:SSEN, disable the Flash

memory interrupts; after setting FSR:SSEN, enable the interrupts.

Figure 26.6-1 Sample Procedure for Setting the Sector Swap Enable Bit (FSR:SSEN)

Start updating Flash data

Start program operation

Copy data

from SA2 to SA1

Start program operation

Complete

Flash data update

Complete

Flash data update

Set FSR:SSEN to "1"

Set FSR:SSEN to "0"

Update data in upper bank

Update data in lower bank

«
...
579
580
581
582
583
...
»

Содержание 8FX











































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8FX

Бренд: National Instruments Страницы: 17

RDX QuikStation 4

Бренд: Tandberg Data Страницы: 2

LoadMaster 1500

Бренд: KEMP Technologies Страницы: 71

Бренд: Teac Страницы: 20

cMT-FHDX Series

Бренд: Maple Systems Страницы: 2

Бренд: NETGEAR Страницы: 2

Surround Dongle

Бренд: Sennheiser Страницы: 18

Бренд: Cytron Technologies Страницы: 13

Бренд: XJTAG Страницы: 9

Бренд: Xilinx Страницы: 8

Бренд: Intel Страницы: 958

Slideaway CL1008

Бренд: ATEN Страницы: 77

Бренд: Konica Minolta Страницы: 31

Бренд: Digital Voice Systems Страницы: 32

Бренд: Extron electronics Страницы: 19

Бренд: Mitsubishi Страницы: 188

Бренд: Abocom Страницы: 70

Lexicon MPX 200

Бренд: Harman Страницы: 77

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды