manualshive.com logo in svg

Fujitsu Siemens Computers Primergy RX220, Руководство по дополнительному обслуживанию

Поделиться
Скачать
Fujitsu Siemens Computers Primergy RX220 Скачать руководство пользователя страница 9

RX220

Service Supplement

9

2

Procedure

V

CAUTION!

The actions described in this manual should only be performed by 
service personnel. 

Ê

First of all please familiarize yourself with the safety instructions in the 

chapter “Safety notes” on page 11

.

Ê

Make sure that all required manuals (see Service-DVD) are available, 
printing out the PDF files if necessary. You will definitely need: 

–

the Operating Manual for the server and 

–

the Options Guide for the server

–

the Technical Manual for the system board.

Ê

Shut down the server correctly, switch it off, pull out the power plug, and 
open the server as described in the 

chapter “Replacement routines” on 

page 17

.

Ê

Replace the defective component, as described in the relevant chapter.

Ê

Close the server.

Ê

Connect up the server cables.

1

Ê

Connect the server to the mains.

1

Ê

Start the operating system.

1

Ê

If necessary, perform the relevant configuration.

1

1

These procedures are described in the Operating Manual.

Содержание Primergy RX220






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды