FUJIPLA AL-MEISTER ALM3222 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 63

FUJIPLA AL-MEISTER ALM3222 Скачать руководство пользователя страница 14

AL-MEISTER ALM3222 Instruction Manual <Rev.2>

Page

14

of

63

2. NAMES AND FUNCTION (cont’d)

2-4. LCD DISPLAY

POWER ON/WARM UP

When powered up the LCD will indicate the model and software
version. The next screen will show the type of film, if installed.

Indicates the machine is being heated up, however operation is

not possible during this time.
LCD may indicate “READY” when RFID tag has been damaged or
is not in place (see information on film roll RFID tag elsewhere in
this manual).

1)

Indicates the set temperature in Fahrenheit.

When the ALM3222 reaches set temperature and regulation begins the buzzer beeps three times.

“READY” appears:



If machine is fully heated.



Under certain conditions if the RFID tag is not in place and machine is not heated.

If the machine has been properly threaded it is ready to be run in automatic mode. If

the machine has

not

been threaded, or if you are unsure that it has been, the START button

should NOT be pressed. To set the film and thread the machine see chapter 4 starting on page
16.

1)  [TEMP] indicates the set temperature in Fahrenheit. See chapter 5-2-1 on page 28.
2)  [SPEED] indicates the set speed in inches per minute. See chapter 5-2-2 on page 29.
3)  [MARGIN] indicates that the trimming and cutting is with or without margin of film on the front and

back (leading and trailing edges) of the laminated paper. NOTE: A “margin” is a (sealed) edge of film
around the laminated paper. See chapter 5-2-5 on page 34.

4) [FINE MODE] indicates the status of Fine Mode. See chapter 5-2-7 on page 37.

«
...
12
13
14
15
16
...
»

Содержание AL-MEISTER ALM3222
































































Отзывы:

Нет отзывов