Error Message
Reason
Solution
Too Long Fiber
• The fiber end-face is placed on the
electrode centerline, or beyond it.
• The cleave length (bare fiber part) is too
long
• Dust or dirt is on the objective lens.
• Press
electrode centerline and the V-groove edge.
• Confirm the setting position of the stripped fiber end on
the fiber cleaver. Check the cleave length.
• Execute the [Dust Check]. Clean the lens when dust or
dirt exists.
Too Dusty
Fiber
• Dust or dirt is on the fiber surface.
• Dust or dirt is on the objective lens.
• [Cleaning Arc] time is too short or “OFF.”
• Completely prepare the fiber again (strip, clean and
cleave).
• Execute the [Dust Check]. Clean the lens if dust or dirt
exists.
• Set the [Cleaning Arc] time to “150ms.” When splicing
carbon coated fibers, set to “200ms.”
ZL/ZR Motor
Overrun
• The fiber is set too far back and does not
reach the splice point.
• The fiber is not set correctly at the
bottom of the V-groove. The fiber is not
located in the Camera’s field of view.
• The cleave length (bare fiber part) is too
short.
• Press
, re-position the fiber again with the
end-face closer to the electrodes.
• Press
, and set the fiber again to seat it correctly
at the bottom of the V-groove.
• Confirm the setting position of the stripped fiber end on
the fiber cleaver. Check the cleave length.
Large Cleave
Angle
• Bad fiber end-face.
• [Cleave Limit] is set too low
• Check the condition of the fiber cleaver. If the blade is
worn, rotate the blade to a new position.
• Increase the [Cleave Limit] to an adequate limit.
Cleave Shape
NG
• Bad fiber end-face.
• Check the condition of the fiber cleaver. If the blade is
worn, rotate the blade to a new position.
Fujikura Ltd.
1-5-1 Kiba, Koto-ku, Tokyo 135-8512 Japan
Phone : +81-3-5606-1164
Fax : +81-3-5606-1534
https://www.fusionsplicer.fujikura.com
Fujikura (CHINA) Co., Ltd.
7
th
Floor, Hang Seng Bank Tower 1000Lujiazui Ring Road,Pudong New Area ShanghaiZIP200120,China
Phone : +86-21-6841-3636
Fax : +86-21-6841-2070
http://www.fujikura.com.cn
Fujikura Asia Ltd.
438A Alexandra Road,Block A Alexandra Technopark #08-03,Singapore 119967
Phone : +65-6278-8955
Fax : +65-6273-7705
http://www.fujikura.com.sg
Fujikura Europe Ltd.
C51 Barwell Business Park, Leatherhead Road, Chessington, Surrey KT9 2NY. UK.
Phone : +44-20-8240-2000
Fax : +44-20-8240-2010
http://www.fujikura.co.uk
AFL
260 Parkway East, Duncan, SC 29334 USA
Phone : +1-800-235-3423
Fax : +1-800 -926-0007
http://www.AFLglobal.com
Authorized Splicer Distributor
Solution of an Error
Contact Address
Q-19_70R-P_E01
Fusion Splicer 19R+/70R+
Quick Reference Guide
, and set the fiber end-face between the
RESET
RESET
RESET
Turning splicer ON
Confirming splice, heater and operation modes
Cleaning coating or sheath of fiber
Placing protection sleeve over fiber
Cleaning fiber
Cleaving fiber
Loading fiber onto splicer
Splicing start automatically
Removing spliced fiber
Centering protection sleeve in tube heater
Heating start automatically
Completed
Stripping fiber
Centering spliced point in tube heater
Visual inspection on LCD during splice
Splice Operation
* Hold the fiber at edge of splicer body.
** Apply tension to the fiber until heater
holds the fiber.
• When splicing only standard SM fibers (ITU-T G.652),
“
SM AUTO
” mode is recommended.
• When splicing different types of fibers, “
AUTO
” mode is
recommended, but splice speed is slow.
• When splicer indicates following message, splice
loss may be high
“Arc discharge is not stable. Electrodes should be
stabilized to reform the arc discharge.”
• Load prepared SM fibers onto splicer in order to
stabilize electrodes. After completeing it, re-splice
fibers.
• When an altitude changes drastically, stabilizing
elctrodes must be excecuted before splicing.
Note
Placing Fiber Holder
• Do not reverse Fiber Holder
when placing onto splicer.
Set in the direction which sees
from the sheet key side and
can read the name of a holder.
*Hold
Marking
**Pull
When using single holder
Adjusting the position of
the fiber coating edge to
holder edge
• Make sure the stripped fiber is free
of coating debris or contamination.
• Use only 99% or better purity alcohol.
• Hold lid firmly
• Free of any gel residue
• Hold this point firmly
Fusion Splicer 19R+/70R+
Quick Reference Guide