Fujiiryoki CYBER-RELAX EC-3800, Руководство пользователя

Страница: 52 / 60

52
Q&A
Q1
Q8
Q9
Q10
Q11
Q13
Q14
Q15
Q16
Q12
Q2
Q3
Q4
Q5
Q6
Q7
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
The remote controller stand is unstable. Why?
_:
Should the remote controller holder be unfastened,
loosen the fixing screws first, and then tighten
them.Check to make sure that the remote
controller stand is not unfastened. If so, tighten it
with a hexagonal wrench.
"^
Put the footrest forward or backward adjustment.
If you are not tall, try to put the backrest at the upright
position, and raise the footrest.
Is leg part unable to descend into the stored
position?
It is unable to descend into the stored position under
leg air operation.Turn leg air operation "OFF". (See
page 25)
I am a patient under the treatment at a hospital.
Are there any problems in using the chair?
Please get your physician's advice. Massage relives
the muscles' stiffness by giving pressure, and
promotes blood circulation. As it may have adverse
effects in certain diseases, be sure to consult your
physician.
Is there no problem in placing a hot carpet under the
chair?
Never do so. Fire may outbreak. The heat
:
There is difference in strength between left and right.
Massaging position appears not be aligned either left and
right not in parallel. Why?
A mechanism is used to allow the two
knead balls tapping alternately for
making massage comfortable. As a
result, a small gap may be produced in
the position between them, and it may
give rise to different massaging strength.
This phenomenon does not come from
the trouble of the chair.
Are there any ways to strengthen the massage
strength?
Try to :
Recline the backrest.
Remove the back pad.
Be deeply seated, and put your body weight on
the backrest.
Adjust the massage strength to be stronger.
The footrest dose not come up automatically to
the stand by position. Why ?
!
than 50°, it dose not come up to the standby
position, even if the button is pressed.
Those who less than 150cm(4'9") or more than
185cm(6'1")in height can use the chair, can't they?
Yes, they can. There is a possibility that the body shape
may not be properly detected at the shoulder position,
:;
Those who are not tall....Put the backrest at
the upright position,and
raise the footrest.
Those who are tall...........Recline the backrest
and lower the footrest.
My arm does not reach the armrest. How can I do so ?
Put the backrest at the upright position, and adjust
the arm position.
After having air-massage of the shoulders and
the arms,my skin becomes red. Why ?
A massage mark is likely to be left on your shoulder
or arm after use. This is because of massage. It will
be disappeared time by time.Please avoid shoulder
exposed dress in the case of air shoulder massage.
"!%
after my body shape is detected. Why ?
After body shape is detected, the knead balls
are ought to move to the shoulder position as
preprogrammed. If the shoulder position still does
not fit in to you, make fine asjustment for the
shoulder position.
Can shoulder unit and the arm unit be removed ?
$ : ! =_
parts exposed dust comes inside, and may cause
trouble in the chair.
In the process of the “DOUBLE STRETCH”
OR “FOOT STRETCH” massage, the chair
occasionally makes a “bang”sound. Why ?
It is likely to make a noise but it is not a break
down. It makes a noise when a leg part and an
electronic actuator are set apart. This is because
of structural matter.
In the process of the Auto mode course, is it
possible to nullify the air-massage function?
Yes, you can.
Please see page 25 for adjustment of air massage
strength.
Normal operational screen is resumed in turning all
air massage modes off under the whole body air
course.
Unable to start body line navigation.
It is unable to be activated when auto course, the
whole body 7minutes short course and stretch
course are selected.
Displacement of
knead balls