manualshive.com logo in svg

FujiFilm FinePix S1500, Руководство по обслуживанию, Страница: 23 / 142

Поделиться
Скачать
FujiFilm FinePix S1500 Скачать руководство пользователя страница 23

FinePix S1500 Service Manual

2-9

2. Disassembly

Confidential: FUJIFILM Service Center Use Only

2-6. 

Removing the MAIN PWB ASSY

(1)  Remove the BATTERY COVER CONST.
(2)  Pull off the LENS FPC MYLAR as shown in the 

figure.

(3)  Unlock the connector and remove the CCD FPC.
(4)  Unlock the connector and remove the LENS FPC.
(5)  Unlock the connector and remove the LENS FPC.
(6)  Remove the solder in 5 locations.
(7)  Remove the solder in 10 locations.
(8)  Remove the TAPE GASKET.
(9)  Remove the 2 screws (M1.7 x L3.5).
(10)  Pull off the BATTERY COVER MYLAR.
(11)  Remove the MAIN PWB ASSY in the direction of the 

arrow.

1

10

8

2

5

6

3

4

6

11

9

7

[Notes on Assembly]

(1) The wire harness is soldered with MAIN PWB ASSY 

as shown in figure.

  (Note that solder doesn't adhere to A point)
(2) Secure the wire harness by Bond.
  Bond: ZS00129-100 (No.1401C)

2

1

A

Содержание FinePix S1500















































































































































Отзывы:

Нет отзывов