Fuji Xerox DocuPrint CM305 df Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 879

background image

2 - 28

Chapter 2 Troubleshooting

077

106

Jam at Front Cover
Open Front Cover
and Remove Paper

<IOT Stop Reservation JAM>
Detect jam when stopped before Fusing Unit in forced
stop mode.

107

Jam at Duplexer
Open Front Cover
Lift Duplexer
and Remove Paper

<IOT Duplex Misfeed JAM>
In the duplex printing mode, the lead edge does not reach
the Regi Sensor when the sheet changes the direction in
the Duplexer after the standby.

108

Jam at Duplexer
Open Front Cover
Lift Duplexer
and Remove Paper

<IOT Duplex JAM>
In the duplex printing mode, the lead edge does not reach
the SSF No Paper Sensor when the sheet changes the
direction in the Duplexer after the standby.

215

Duplexer Error
Error 077-215
Restart Printer

<IOT Duplexer Failure>
The error is detected by Duplexer communication check.

300

Front Cover Open.
Close Front Cover.

<IOT Cover Front Open>
The Front Cover is open.

301

Side Door Open.
Close Side Door.

<IOT Side Cover Open>
The Toner Access Cover is open.

900

Jam at Exit
Open Front Cover
and Remove Paper

<IOT Exit JAM>
The paper remains at the Exit Sensor.

901

Jam at Front Cover
Open Front Cover
and Remove Paper

<IOT Remain Registration JAM>
The paper remains at the Regi Sensor.

907

Jam at Duplexer
Open Front Cover
Lift Duplexer
and Remove Paper

<IOT Remain Duplex JAM>
The paper remains at the Duplex area.

091

402

Ready to Print
Replace Imaging Unit
Soon.
Life Almost Over.

<IOT PHD Life Pre Warning>
The PHD Unit is approaching the replacement time.

912

Imaging Unit Error
Remove Imaging
Unit and
Confirm all Yellow
Ribons
are Removed

<PHD Tape Staying>
Detect the tape staying on the PHD Unit.

916

CRUM Error
Imaging Unit
Error 091-916
Restart Printer

<IOT PHD CRUM ID Error>
An unsupported PHD Unit is detected.

935

Replace
Imaging Unit

<IOT PHD Life Over>
The PHD Unit has reached the replacement time.

941

Waste Full
Yellow Cartridge

<IOT CRU Waste (Y) Full>
Waste Toner (Y) Counter value has reached replacement
time.

942

Waste Full
Magenta Cartridge

<IOT CRU Waste (M) Full>
Waste Toner (M) Counter value has reached replacement
time.

943

Waste Full
Cyan Cartridge

<IOT CRU Waste (C) Full>
Waste Toner (C) Counter value has reached replacement
time.

Status

Code

Error Message

Status Contents

FIP to be

referred

LCD

«
...
60
61
62
63
64
...
»

Содержание DocuPrint CM305 df
















































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint CM305 df

Бренд: Felix printers Страницы: 9

Бренд: Felix printers Страницы: 15

Бренд: Felix printers Страницы: 15

Бренд: Oki Страницы: 62

Бренд: TallyGenicom Страницы: 144

Бренд: Intamsys Страницы: 5

Бренд: Canon Страницы: 32

imageRUNNER ADVANCE DX C478iZ

Бренд: Canon Страницы: 208

imageRUNNER ADVANCE DX C477iFZ

Бренд: Canon Страницы: 92

Бренд: Oki Страницы: 2

Бренд: Olivetti Страницы: 69

Бренд: Aficio Страницы: 156

Бренд: Evolis Страницы: 63

Бренд: Lexmark Страницы: 8

SEH InterCon PS54a-G

Бренд: SEH Страницы: 24

Бренд: VORON Страницы: 73

Бренд: StarTech.com Страницы: 13

Бренд: Sagem Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды