Fuji Xerox DocuPrint CM305 df Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 879

background image

1 - 1

Chapter 1 Service Call Procedure

1.1

Before Starting the Servicing

1.1.1 Safety

To prevent any accident that may occur during maintenance servicing, any WARNING or CAUTION
regarding the servicing must be strictly observed. Do not perform any hazardous operation.

1. Power Supply

To prevent electrical shocks, burns, or injury, etc., be sure to switch OFF the machine and
disconnect the plug before starting the maintenance servicing. If the machine has to be switched
ON, such as when measuring the voltage, take extra care to prevent an electrical shock.

2. Drive Area

Never inspect or lubricate the drive area such as the gears during the machine operation.

3. Heavy Parts

The weight of the machine is 29.6kg. When moving the machine to ensure sufficient working
space, take extra care to prevent back pain.

4. Safety Device

See that safety devices for preventing mechanical accidents, such as fuses, circuit breakers,
interlock switches, etc., and those for protecting customers from injury, such as panels and
covers, function properly. Modifications that hinder the function of any safety devices are strictly
prohibited.

5. Installing and removing the parts

The edge of parts and covers may be sharp, take care not to touch them. If the oil gets onto your
hand, wipe it off before getting on with the servicing. When removing parts or cables, do not pull
them out by force but remove them slowly.

6. Specified Tools

Follow the instruction when a tool is specified.

7. Organic Solvents

When using an organic solvent such as the Drum Cleaner or Machine Cleaner, pay attention to
the following:
• Ensure good ventilation in the room to prevent too much intake of the solvent.
• Do not use heated solvent.
• Keep away from fire.
• Wash your hands throughly after use.

8. Cleaning the Toner and Developer

As the toner may cause a dust explosion, sweep the spilt toner into a waste container. When
using a cleaner to clean the remaining toner, be sure to use the FX standard toner-proof cleaner
and not a customer's cleaner. Also, as the developer also contains toner, exercise the same
caution during cleaning.

9. Modifications

If any modifications are deemed necessary for the printer, submit an Application for Approval of
Modification prior to performing any work.

«
...
17
18
19
20
21
...
»

Содержание DocuPrint CM305 df
















































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint CM305 df

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 44

Бренд: Oki Страницы: 13

Бренд: Oki Страницы: 20

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 28

Бренд: Oki Страницы: 40

Бренд: TallyGenicom Страницы: 2

Бренд: JCM Страницы: 22

Бренд: Oki Страницы: 207

Бренд: Oki Страницы: 56

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 8

Бренд: Oki Страницы: 16

Бренд: Oki Страницы: 323

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 150

Бренд: Oki Страницы: 341

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды