Fuji Xerox ApeosPort-V 4070 Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 719

background image

Common Service Settings

131

Tools

5

Last operation on the machine

J

Low Power mode

J

Sleep mode

For more information on the setting procedure, refer to "Power Saver Mode" (P.25).

Note

•

You cannot configure the machine not to switch to the Low Power mode or the Sleep mode.

From Last Operation to Low Power Mode

Specify a time period between 1 and 240 minutes in 1 minute increments to enter the Low
Power mode after the last operation.

From Last Operation to Sleep Mode

Specify a time period between 1 to 240 minutes in 1 minute increments to enter the Sleep
mode after the last operation.

Note

•

Configure the [From Last Operation to Sleep Mode] time to be same or longer than the [From Last
Operation to Low Power Mode] time.

•

The machine enters Sleep mode without entering Low Power mode when the [From Last Operation
to Low Power Mode] time is same as the [From Last Operation to Sleep Mode] time.

Enter Power Saver after Printing Ends

Set when to enter the Power Saver mode after a print job or printing of fax/Internet fax
documents is finished.

15 seconds after Auto Printing Ends

Enters Sleep mode in 15 seconds.

According to Power Saver Timer Settings

Enters Low Power mode or Sleep mode according to the period specified in [Power Saver
Timers].

For more information on the setting procedure, refer to "Power Saver Mode" (P.25).

Power Saver Deactivation

Select whether to disable the Power Saver mode fully or partially when exiting the mode.

Deactivate All

All devices of the machine exit the Power Saver mode.

Deactivate Partially As Required

Only the devices necessary for the operation exit the Power Saver mode.

You can select from [Always On] or [When Printing / Job Auto Processing].

Scheduled Power Off

You can set a time for the machine to be automatically turned off.

Disabled

Does not turn off the machine automatically.

Enabled

Set a time for the machine to be automatically turned off.

Note

•

[Disabled] is set by default.

•

Even when [Enabled] is set, the machine will not be automatically turned off during an error (such as
paper jam) or processing (such as copying, printing, interruption).

«
...
129
130
131
132
133
...
»

Содержание ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ApeosPort-V 4070

Бренд: LabelTac Страницы: 2

PowerShot S330 Digital ELPH

Бренд: Canon Страницы: 2

PowerShot S400 Digital Elph

Бренд: Canon Страницы: 271

Бренд: Canon Страницы: 6

PowerShot S330 Digital ELPH

Бренд: Canon Страницы: 25

Бренд: Lexmark Страницы: 500

Бренд: Konica Minolta Страницы: 20

Бренд: Colorjet Страницы: 52

AficioSP C410DN

Бренд: Ricoh Страницы: 204

Бренд: Partner Страницы: 34

Бренд: Tektronix Страницы: 42

Бренд: Citizen Страницы: 4

ESP 3200 Series

Бренд: Kodak Страницы: 90

WorkCentre 3615DN

Бренд: Xerox Страницы: 4

Бренд: Lexmark Страницы: 729

Бренд: TransAct Страницы: 45

Бренд: Riso Страницы: 82

Бренд: OmniPrint Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды