FSM 1700MM Tigercat Скачать руководство пользователя | Manualshive

Страница: 7 / 32

background image

6

1.Slide the wing tube into the fuselage. Install the left and right wing (with nacelles on) over the wing

tube and into the wing slot of the fuselage (fig3).

Notice: The connectors on both sides should be attached precisely and firmly.

2.Secure the left and right wings to the fuselage using the screws included (fig4).

3.Connect the power lines and signal lines from the wings to the parallel power connectors (with UBEC)

and Y-harness connected to the receiver in the fuselage (fig5)

fig3

Model Assembly

HKM3.0*16

fig4

fig5

«
...
5
6
7
8
9
...
»

Содержание 1700MM Tigercat

































Отзывы:

Нет отзывов

Похожие инструкции для 1700MM Tigercat

Бренд: K'Nex Страницы: 30

Бренд: K'Nex Страницы: 44

40 MODEL BUILDING SET

Бренд: K'Nex Страницы: 13

Бренд: K'Nex Education Страницы: 35

Бренд: K'Nex Страницы: 2

Бренд: K'Nex Education Страницы: 24

100 MODEL IMAGINE BUILDING SET

Бренд: K'Nex Страницы: 78

100 MODEL IMAGINE BUILDING SET

Бренд: K'Nex Страницы: 64

Бренд: K'Nex Страницы: 32

Бренд: K'Nex Страницы: 24

Бренд: Eduard Страницы: 6

JAMMIN' JEEP T8396

Бренд: Barbie Страницы: 24

Бренд: Majik Страницы: 8

Dystraction backyard /Indoor F3A

Бренд: Stevens AeroModel Страницы: 19

harbour tug FAIRPLAY

Бренд: ROBBE Страницы: 14

Бренд: BLOTZ Страницы: 3

Education 79318

Бренд: K'Nex Страницы: 6

Бренд: Liliput Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды