background image

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and

others or result in damage to the product or the property of others. This model is controlled by a radio signal subject

to interference from many sources outside your control. This interference can cause momentary loss of control so it

is advisable to always keep a safe distance in all directions around your model, as this margin will help avoid collisions

or injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

·Never operate your model with low transmitter batteries.

·Always operate your model in an open area away from cars, traffic or people.

·Avoid operating your model in the street where injury or damage can occur.

·Never operate the model in populated areas for any reason.

·Carefully follow the directions and warnings for this and any optional support equipment you use (chargers,

 rechargeable battery packs, etc.)

·Keep all chemicals, small parts and anything electrical out of the reach of children.

·Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and

 protected for this purpose.

·Never lick or place any part of your model in your mouth as it could cause serious injury or even death.

Lithium Polymer (Li-Po) Battery Warning

CAUTION: Always follow the manufacturer’s instructions for safe use and disposal of batteries. Fire, property

damage, or serious injury can result from the mishandling of Li-Po batteries.

By handling, charging or using a Li-Po Battery you assume all risks associated with lithium batteries.

If at any time the batteries begin to swell or balloon, discontinue use immediately!

Always store the batteries at room temperature in a dry area to extend the life of the battery. Always transport

or temporarily store the battery at a temperature range of 40-120F. Do not store the battery or model in a car or in direct 

sunlight. If stored in a hot car, the battery can be damaged or even catch fire.

Never use a Ni-Mh Charger to charge Li-Po Batteries. Failure to charge the battery with a Li-Po compatible charger

may cause fire resulting in personal injury and property damage.

Never discharge Li-Po Cells below 3V.

Never leave charging batteries unattended.

Never charge damaged batteries.

Use a battery charger that is designed to safely charge the Li-Po Battery. Read the charger instructions carefully

before use. When charging the battery, make certain the battery is on a heat resistant surface. It is also highly

recommended to place the Li-Po Battery inside a fire resistant charging bag readily available at hobby shops or

online.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. 

Failure to operate the product correctly can result in damage to the product, personal property and cause serious 

injury. 

This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and failure 

to do so could result in injury or damage to the product or other property. This product is not intended for use by 

children without direct adult supervision. 

This manual contains instructions for safety operation and maintenance. It is essential to read and follow all the 

instructions and warnings in the manual prior to assembly, setup or use, in order to operate and avoid damage or 

serious injury.

Содержание 1700MM Tigercat

































Отзывы: