background image

3

I

O

Se ial Number 

Tag

Ambient Air Filter

Electrical

Connection

Control

Panel

Air Inlet

Connection

Serial 

Number

Tag

Drain 

Connection

Air Outlet

Connection

Separator and

Integral Filter

Left Side

Front

Back

Right Side

Strainer

(shipped

separately)

Drain

Mechanism

Pipe Nipple

2.  Location in the compressed air system

A. 

  Maximum working pressure - 250 psig, 

17.6 kgf/cm

2

.  Do not exceed unit’s Maximum Working 

Pressure.

1)  For maximum capacity, install unit in air system 

at highest pressure possible (e.g. before pressure 

reducing valves) 

2)  For maximum capacity, install unit at coolest com-

pressed air temperature possible.  Maximum inlet 

compressed air temperature: 180°F, 82°C.  If inlet 

air exceeds this temperature, precool the air by 

extending the piping between the compressor and 

the dryer.  

B.  Air Outlet - Connect air outlet to downstream air lines.

C.  By-pass piping - If servicing the unit without interrupt-

ing the air supply is desired, piping should include inlet 

and outlet isolation valves and an air by-pass valve.

D.  Condensate drain - It is advisable to connect drain 

outlet to the condensate drainage system.

NOTE: Drain discharge is at system pressure. Drain line 

should be anchored to prevent whipping.

1.4  Electrical connections 

A.  Dryer is designed to operate on power supply (voltage) 

listed on serial number tag located on the back of the 

dryer.

B.  Dryer is supplied with an electrical cord.  Install in re-

ceptacle of proper voltage.       

NOTE:  Models 50 and 75 (115v only) - Install plug 

in receptacle rated for 20 amps.  Units are sup-

plied with 20 amp plug.

NOTE: Refrigeration system is designed to run continu-

ously and should NOT be wired to cycle on/off with the air 

compressor.  

1.0 INSTALLATION

1.1  Location  

A.  Air compressor intake - Locate air compressor so that 

contaminants potentially harmful to the dryer are not 

drawn into the air system.  

B.  Free air flow -  Do not block either side of the cabinet.  

Observe minimum installation clearances as shown.

1.2 Mounting 

Dryer is suitable for floor or shelf mounting.

1.3  Piping connections 

A.  Air Inlet - Connect compressed 

air line from air compressor to 

air inlet using strainer supplied.

1.  Install strainer (included in 

shipping carton) prior to 

dryer inlet using pipe nipple 

supplied or other piping as 

required.

NOTE: Observe flow direction arrows on strainer.

NOTE: Install strainer where it is easily accessible for clean-

ing.

NOTE: Use vibration dampener, if vibration exists in air line 

at inlet to dryer.

24"

12"

wall

6"

36"

Plug

Содержание RNH100

















Отзывы: