Frymaster HLZ 18 Скачать руководство пользователя

Страница: 12 / 25

Frymaster L.L.C., 8700 Line Avenue 71106, P.O. Box 51000, Shreveport, Louisiana 71135-1000

318-865-1711 FAX 318-862-2394

Printed in the United States

Service Hotline

Page

1-800-24-FRYER

9. SERVICE INFORMATION

9.1 PARTS LIST

This parts list is correlated with the HLZ interior view found in section 9-2.

Item

Description

Part

Number

Transformer, 208V/240V/12V

807-0979

Air Heater, 208V only

807-2945

Air Heater, 240V only

807-3011

Shield, HLZ Heater

900-8073

Air RTD Probe

807-3036

Bracket, RTD/Thermocouple

900-8086

Delivery Air Back W/A

823-2741

Air Thermocouple

807-3043

HLZ 22 Plate, Heater with RTD
and Thermocouple, 208V/240V
(22”x15.5”)

806-9238

HLZ 18 Plate, Heater with RTD
and Thermocouple, 208/240V
(22”x12”)

806-9239

Plug Assembly, Computer

806-9146

Relay, Solid State Service Kit

826-1508

Relay, Latching

807-3021

Blower, 208V/240V

807-2953

Item #

Description

Part

Number

Fuse Block

807-2820

Fuse, 20A

807-2819

Cord Set, Twist Lock, HLZ

807-3020

Not Shown

RTV#108 Silicone Rubber

811-0511

Not Shown

Gasket, HLZ Plate/Cowl

816-0418

Not Shown

Filter Screen

810-1724

Not Shown

Acrylic Tape, Double-
Sided

811-0953

Not Shown

Computer Assembly, HLZ

806-9247

Not Shown

Cowl Assembly

823-2745

Not Shown

Cowl Tinnerman Clips

809-0448

Not Shown

Front Delivery Air W/A

823-2742

Not Shown

Lug, Grounding 14 GA

807-2972

Not Shown

Pad, HLZ Leg

816-0410

* Note: Burger Bumpers are not used on units built after
10/98.

9.2 Interior view of an HLZ (Cowl Assembly removed)

Blower assembly

Fuses

Relays

•

Air RTD Probe

•

Air

Thermocouple

Содержание HLZ 18


























Результаты поиска

Содержание HLZ 18

Отзывы:

Похожие инструкции для HLZ 18

Бренды по названию

Популярные бренды

Frymaster HLZ 18, Руководство по обслуживанию

Результаты поиска

Содержание HLZ 18

Отзывы:

Похожие инструкции для HLZ 18

Бренды по названию

Популярные бренды