background image

1-3

 

1.5  Shipping Damage Claim Procedure 

 

 

What to do if your equipment arrives damaged:

 

 
Please note that this equipment was carefully inspected and packed by skilled personnel before 
leaving the factory. The freight company assumes full responsibility for safe delivery upon 
acceptance of the equipment. 
 
1.  File Claim for Damages Immediately—Regardless of extent of damage. 
 
2.  Visible Loss or Damage—Be sure this is noted on the freight bill or express receipt and is signed 

by the person making the delivery.

 

 
3.

 

Concealed Loss or Damage—If damage is unnoticed until equipment is unpacked, notify the 
freight company or carrier immediately and file a concealed damage claim. This should be done 
within 15 days of date of delivery. Be sure to retain container for inspection. 

 

1.6 Service 

Information

 

 

For non-routine maintenance or repairs, or for service information, contact your local Frymaster 
Dean Factory Authorized Service Center (FASC). Service information may also be obtained by 
calling the Frymaster Technical Services Department (1-800-551-8633 or 1-318-865-1711).  In order 
to assist you quickly, the FASC or Service Department representative will require certain 
information about your equipment.  Most of this information is printed on a data plate affixed to the 
inside of the fryer door.  A list of common repair parts is provided in Chapter X of this manual.  
Parts orders should be placed directly with your local FASC or distributor.  Included with fryers 
when shipped from the factory is a list of Frymaster Dean FASCs.  If you do not have access to this 
list, contact the Frymaster Dean Service Department. 
  
The following information will be needed in order to assist you efficiently: 
 

Model Number_________________________  

 

Serial Number _________________________  

 

Voltage ______________________________  

 

Nature of the Problem ___________________  

 

____________________________________  

 

____________________________________  

 

 

RETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USE.

 

 
 

Содержание 824E































Отзывы: