Frymaster 3000 Скачать руководство пользователя страница 25

Страница: 25 / 28

2-3

PROBLEM

PROBABLE CAUSES

CORRECTIVE ACTION

Controller displays

HEATING

FAILURE

Contactor issue, gas valve off,
failed controller, failed
transformer, open high-limit
thermostat.

It is normal for this message to appear during
startup if a gas fryer’s lines have air in them.
Check that the gas valve is on. If it continues,
shut the fryer down and call your FAS for
assistance.

Controller displays

SERVICE

REQUIRED

followed

by an error message.

An error has occurred which
requires a service technician.

Press



(NO) to continue cooking and call

your FAS for assistance. In some cases,
cooking may not be allowed.

2.2.2 Filtration

Problems

PROBLEM

PROBABLE CAUSES

CORRECTIVE ACTION

Controller

displays

IS VAT

FULL? YES

after a

filtration.

A. Normal after filtering or filling.

A. Press



(YES) if the vat is full, otherwise

press



(NO) and follow prompts.

CLEAN, POLISH,

FILTER OR

DISPOSE

won’t

start.

Temperature too low or controller
displays OFF.

Ensure fryer is at 300°F (148°C) for Polish and
250°F (121°C) for Clean, Filter or Dispose;
ensure the controller is ON.

Controller displays

WAIT FOR

Filter

A. Another function is still in

process.

B. MIB has not cleared checking

system.??

A. Wait until the previous function ends to

start another filtration cycle.

B. Wait one minute and try again.

Controller displays

INSERT pan

A. Normal during Change Filter

Paper routine.

A. Insert pan and press



(CONFIRM)

button.

Controller displays

OIL IN DRAIN

PAN / CONFIRM

Drain valve open or possibility that
oil is in drain pan.

Press



(CONFIRM) and follow directions for

FILL VAT FROM DRAIN PAN.

Controller displays

FLT DYLD

A filter cycle has been delayed.

This is a normal display when a filter has been
delayed. After the next filter prompt press
YES to filter.

Controller displays

POL DYLD

A polish cycle has been delayed.

This is a normal display when a polish has
been delayed. After the next polish prompt
press YES.

Wait for

Clean

Clean and filter was selected with
oil temperature below 250°F
(121°C).

Allow oil to heat to 250°F (121°C).

Wait for

dispose

Dispose was selected with the oil
temperature below 250°F (121°C).

Allow oil to heat to 250°F (121°C).

Содержание 3000





























Результаты поиска

Содержание 3000

Отзывы:

Похожие инструкции для 3000

Бренды по названию

Популярные бренды

Frymaster 3000, Руководство по эксплуатации

Результаты поиска

Содержание 3000

Отзывы:

Похожие инструкции для 3000

Бренды по названию

Популярные бренды