Fryette PowerStation PS1 Скачать руководство пользователя страница 10

TROUBLESHOOTING GUIDE

SPECIFICATIONS

WON’T TURN ON

1.  Make sure AC cord is securely connected at 

both ends.

2.  Verify the power source with something you 

know works.

3.  Check the mains fuse, and replace if necessary. 

If it blows again, refer to qualified service personnel.

NO SOUND

1.  Check input cable.

2.  Check volume controls.

3.  Make sure the amplifier volume and/or gain 

controls are turned up.

4.  Check to see if the effects loop is connected 

correctly.

5.  Check speaker cable to see if it is disconnected 

or shorted.

6.  Make sure that the impedance selector is fully 

engaged in its detent.

7.  Check the standby switch.

8.  Check for a blown speaker.

9.  Check the mains fuse, and replace if necessary. 

If it blows again, refer to qualified service personnel.

WON’T SWITCH TO OPERATE

1.  Check the mains fuse, and replace if neces-

sary. If it blows again, refer to qualified service 

personnel.

EFFECTS NOT OPERATING

1.  Make sure effects send and return cables are 

good and properly connected.

RUNNING HOT

1.  Make sure that the unit has adequate ventilation.

2.  Make sure that the impedance selector is set to 

the proper impedance.

3.  Power tubes may be drawing excessive current 

(refer to qualified service personnel).

NOTE: Always set the amplifier to standby when 

taking breaks and turn the amplifier off when 

not in use. This will extend tube life and improve 

long term reliability.

DISTORTION

1.  Check the impedance setting.

2.  Check the speaker cable for shorts.

3.  Check the speaker.

4.  Check the signal level at other devices in the 

signal path or in the loop.

5.  Power tubes may be weak (refer to qualified 

service personnel).

BLOWING MAINS FUSE

1.  Bad power tube or other internal power supply 

component (refer to qualified service personnel).

MODEL: POWER STATION

MODEL NUMBER: PS1.

POWER REQUIREMENT: 180W

POWER AMP OUTPUT: 50W RMS @ 5% THD,

1kHz sine into 8Ω

INPUT IMPEDANCE: 4Ω/8Ω/16Ω (selectable)

OUTPUT IMPEDANCE: 4Ω/8Ω/16Ω (selectable)

FUSE:

100V UNITS: 

T3.15A, 125/250V.

120V UNITS: 

T3A, 250V.

220V-240V UNITS: 

T1.6A, 250V.

DIMENSIONS:

HEIGHT:

 3.6 in (9.1 cm)

WIDTH: 

14 in (35.5 cm)

DEPTH:

 9 in (22.8 cm)

WEIGHT: 15 lb (6.8 kg)

Product specifications are subject to change without notice.

Содержание PowerStation PS1













Отзывы: