FrSky Electronic Co., Ltd
Website:www.frsky-rc.com E-mail:[email protected] Technical Support: [email protected]
FrSky Electronic Co., Ltd
Website:www.frsky-rc.com E-mail: [email protected] Technical Support: [email protected]
www.frsky-rc.com
www.frsky-rc.com
4. Upgrade FSD
3.6 IDSET Screen:
3.7 INFO Screen:
Follow the steps below to change the data names from page 1 to page 3:
Step 1: Short press the rotate switch
Step 2: Use the rotate switch to choose the position you want to change
Step 3: Short press the rotate switch
Step 4: Use the rotate switch and find the data name you want and short press rotate switch to confirm.
Note: Data screen has 5 pages in total. Just enable the GPS sensor and Lipo Voltage
Sensor on the SYSTEM screen to enable the page 4 and 5.
Page 4: GPS data
Latitu: Latitude (unit: degree)
Longi: Longitude (unit: degree)
Distance: Distance from your first position
to your flight position now
Date: Y/M/D
00 : 03 : 43
P4
Latitu:
Longi:
Distance:
Date:
0.0000
0.0000
0
2000-00-00
Page 5: Lipo Voltage Sensor data
Total: Total voltage, cell number and cell
voltage of all the batteries connected.
Total: 0.00 0s P5
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
Data
SWR
RSSI
RBat
A1 A2
A3 A4
A3_1 A4_1
Valt
Vspd
Vcu1 Vcu2 Vcu3 Vcu4
CUR1 CUR2 CUR3 CUR4
TEM1 TEM2
RPM1 RPM2 RPM3 RPM4
Fuel
Altg
Spdg
CC1 CC2 CC3 CC4
PWR1 PWR2 PWR3 PWR4
Cors
Scur
Vol-
Meaning
Antenna Detection
Received Signal Strength Indicator
Receiver Battery Voltage
Analog Voltage (Receiver)
Analog Voltage (S.port to UART Host)
Analog voltage (S.port to UART Remote)
Altitude of Variometer Sensor
Vertical Speed
Voltage of Current Sensor
Current of Current Sensor
Temperature
RPM
Fuel Level
Altitude of GPS
Speed of GPS
Current Consumption
Power of Current Sensor
Direction of GPS
Sum Current of Current Sensor
the Lowest Voltage among all Cells
PhyID
01
NewPyID
01
GNum
01
NewGNum
01
Tip: Finished
SEND
RESET
PhyID
physical ID of the sensor
NewPyID
new physical ID you want to set for the sensor
SEND
RESET
Tip
GNum
group number of the sensor
NewGNum
new group number you want to set for the sensor
send your settings to the sensor
reset your settings to default
the result of your settings
TIPS: Vcu, CUR, TEM1, RPM, CC, PWR have several data because of the different groups.
Follow the steps below to set “PhyID” and “GNum” for S.Port Sensors:
Step 1: Use “rotate switch” to choose “IDSET”;
Step 2: Use rotate switch to choose New PyID and/or New GNum and short press;
Step 3: Set the number for the sensor and short press “rotate switch”;
Step 4: Short press “SEND” and confirm “Tip” indicates “Finished”.
FrSky Sport Dashboard
Firmware Vers: v1.52
Eeprom Vers: v0.3
FrSky Sport Dashboard
Firmware Vers: v1.52
Eeprom Vers: v0.3
Follow the steps below to upgrade the FSD firmware:
Step 1: Create a new folder named “Firmware” in the TF card by PC.
Step 2: Download the firmware from FrSky website and put the .bin file into the “Firmware” folder.
Step 3: Insert the TF card back into the FSD card slot.
Step 4: Hold “Page” button while power on the FSD.
Step 5: Use “rotate switch” to choose “YES” to reflash (or “NO” to quit) and short press “rotate switch” to confirm the
upgrade.
FrSky Sport Dashboard
Boot Mode Ver-0.4
Yes to Reflash or
NO to quit?
Ready to upgrade
YES
NO
