Set up the receiver channel and radio switches
Move to the [SxR] tool, determine the [Wing Type] & [Mounting Type];
[Gain] and [Offset] configurations of flight modes
Check whether the reaction of the wing/servo is in line with the flight attitude caption below in the
[Auto-Level] mode. If not, please try to invert the corresponding channel output in the [SxR] tool.
Version
1.0
Instruction Manual for FrSky ARCHER PLUS SR10+ Receiver
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us : [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Version
1.0
Instruction Manual for FrSky ARCHER PLUS SR10+ Receiver
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us : [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Version
1.0
Instruction Manual for FrSky ARCHER PLUS SR10+ Receiver
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us : [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Version
1.0
Instruction Manual for FrSky ARCHER PLUS SR10+ Receiver
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us : [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
When the plane is rotated left or right
(Roll), ailerons should have the correcting
actions as illustrated above.
When the plane is rotated up or down
(Pitch), elevators should have the
correcting actions as illustrated above.
When the plane is rotated to left or right
(Yaw), rudders should have the correct-
ing actions as illustrated above.
Inspection of flight attitude
To ensure flight safety, checking the compensation direction of the model is strongly recommended.
Activating auto level mode will produce a strong deflection on AIL and ELE, which is used to check the response
of aileron and elevator. Also, activating Knife-edge and Hover mode will have the same reaction on the rudder.
Note: If the compensation direction is incorrect, please reverse the corresponding channel as illustrated
below.
After changing the compensation direction, make sure to check it again on the actual model.
1
3
2
2
1
4
4
3
1
2
1
2
Wing Type
Mounting Type
How to set the flight modes
Quick Mode
It supports stabilization mode, auto-level mode, and manual (six-axis off) mode and configured through CH10.
What’s more, an Emergency mode is added to configure automatic level mode default through CH12. The precise
configuration is written below.
Note: The default mode of SR10+ is Quick Mode.
- If Quick mode is applied, there is no Knife
Edge or (3D) Hover mode.
- CH11 is not used when using Quick Mode.
The Stabilization series receivers fit multiple types of models, the model type can be changed via different tools (like STAB RX.lua,
ETHOS SxR, etc.), and this series receivers can also be used as a standard receiver by disabling the gyro function (SXR Enable by
default).
Flight Mode
None
Stabilization Mode
Automatical Level Mode
Emergency Mode (Automatic Level Mode)
Position
SW Down
SW Mid
SW Up
SW Down
Channel
CH10
CH12
Flight Mode
Conventional mode
Layout
CH10 SW-mid
Off
CH10 (3 pos SW)
CH11(3 pos SW)
Stabilization
CH10>M+H
(CH10 SW Down)
M-H<CH11<M+H
(CH11 SW Mid)
Automatic level
CH10>M+H
(CH10 SW Down)
CH11>M+H
(CH11 SW Down)
Hover
CH10>M+H
(CH10 SW Down)
CH11<M-H
(CH11 SW Up)
Knife-Edge
CH10<M-H
(CH10 SW Up)
M-H<CH11<M+H
(CH11 SW Mid)
Flight mode
Refer to the Channel List to set the channel and
switches. The switch setting of CH9-12 on the picture
is for reference.
Check whether the reaction of the wing/servo is in line with the radio stick operation in the [Manual]
mode. If not, please try to invert the corresponding channel output by pressing the channel bar in the
[Output] tool.
Stabilize Gain
Auto Level Gain
Hover Gain
Knife-Edge Gain
1
2
3
Auto Level Offset Angle
Hover Offset Angle
Knife-Edge Offset Angle
1
2
3
Note 1: To do the Self-Check of the stabilization device, please ensure the [SxR] function is enabled.
Enter the [SxR] tool and turn On the [SxR Enable], then quit the [SxR] tool and back into this tool again,
now the [Self-Check] function is capable to enable.
Self Check
1. Put the throttle to 0, and keep the other channels in the center position.
2. Move to [Device Config] and enter the [SxR] tool to turn on [Self Check], then the blue LED light turns on.
Once the blue LED starts flashing, we can calibrate the maximum travel of stick channels (including the
throttle channel).
3. If the calibration is completed, the LED turns off and the servos react left and right to indicate that the
calibration process is completed.
Do the Self-Check in the [SxR] tool.
1
[Device Configuration] → [SxR]
Self Check
1
Delta wing & Flying wing & V-tail
The available flight modes can be assigned to CH10 with a three-position switch.
Flight mode
Stabilization
Auto Level
Off
CH10
CH10>M+H
(CH10 SW Down)
CH10<M-H
(CH10 SW Up)
CH10 SW-mid
Layout of Delta wing / Flying wing
Layout of V-tail
