background image

Safety 9

5WPMAN0511 (Rev. 5/9/2008)

GUARD MISSING.

DO NOT OPERATE.

DANGER

33347E

DANGER

DANGER

GUARD MISSING.

DO NOT OPERATE.

FALLING OFF CAN RESULT IN BEING RUN OVER.

„

Tractor must be equipped with ROPS (or ROPS CAB) and seat
belt. Keep foldable ROPS systems in “locked up” position at all
times.

„

Buckle Up! Keep seat belt securely fastened.

„

Allow no riders.

RAISED EQUIPMENT CAN DROP AND CRUSH.

„

Before working underneath, follow all instructions and safety rules in
operator’s manual and securely block up all corners of equipment
with jack stands.

„

Securely blocking prevents equipment dropping from hydraulic leak-
down, hydraulic system failures or mechanical component failures.

FALLING OFF OR FAILING TO BLOCK SECURELY CAN
RESULT IN SERIOUS INJURY OR DEATH.

WARNING

18865--C

If shaft connection is visible, shield 
is missing. Replace shield before 
operating equipment.

DANG

NGER

ER

1004114

7 - 5WP18865

8 - 5WP1004114

9 - 5WP33347

5 - 5WP18864

6 - 5WP1002423

CRUSHING AND PINCHING HAZARD

 

Be extremely careful handling various parts of 

the machine. They are heavy and hands, fingers, 
feet, and other body parts could be crushed or 
pinched between tractor and implement.

  Operate tractor controls from tractor seat only. 

  Do not stand between tractor and implement 

when tractor is in gear. 

  Make sure parking brake is engaged before 

going between tractor and implement.

  Stand clear of machine while in operation or 

when it is being raised or lowered. 

FAILURE TO FOLLOW THESE 

INSTRUCTIONS COULD RESULT IN 

SERIOUS INJURY OR DEATH. 

 

WARNING

1003751-A

10 - 5WP1003751

                            

     

 

                       

   

   

     

         

 

 

 

                  

          

DANGER

ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH

KEEP AWAY!

DO NOT OPERATE WITHOUT -

  All driveline guards, tractor and 

equipment shields in place

  Drivelines securely attached at both ends

  Driveline guards that turn freely on 

driveline

18864-C

(Safety Decals continued from previous page)

WARNING

TO AVOID SERIOUS INJURY OR DEATH:

 Read Operator's Manual before operating, 

servicing or repairing equipment. Follow all 
safety rules and instructions. (Manuals are 
available from your selling dealer.)

 Never allow riders.

 Keep bystanders away from equipment during 

operation.

 Operate from tractor seat only.

 Keep all shields in place and in good condition.

 Lower equipment to ground, stop engine, 

remove key and set brake before dismounting 
tractor.

 Never allow children or untrained persons to 

operate equipment.

 Do not transport towed or semi-mounted units 

over 20 MPH.

FAILURE TO FOLLOW THESE INSTRUCTIONS 
CAN RESULT IN INJURY OR DEATH.

1002423-B

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

Содержание GM1060

















































Отзывы: