background image

RRSTUNI_REV_A05

© 2019 FRONT RUNNER VEHICLE OUTFITTERS

slimline ii tray

universal assembly

instructions 

RRSTUNI

ENG

1

Thank you for purchasing a Front Runner Slimline II Tray.

Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received. 

Refer to Page 2 for a list of all the components, quantities and tools required.

READ ME !

IMPORTANT WARNING!

IT  IS  CRITICAL  THAT  ALL  FRONT  RUNNER  PRODUCTS  BE  PROPERLY  AND  SECURELY  ASSEMBLED  AND  ATTACHED  TO  YOUR  VEHICLE.  IMPROPER  ATTACHMENT  COULD  
RESULT  IN  AN  AUTOMOBILE  ACCIDENT,  AND  COULD  CAUSE  SERIOUS  BODILY  INJURY  OR  DEATH.  YOU  ARE  RESPONSIBLE  FOR  ASSEMBLING  AND  SECURING  ALL  FRONT 
RUNNER  PRODUCTS  TO  YOUR  VEHICLE,  CHECKING  THE  ATTACHMENTS  PRIOR  TO  USE,  AND  PERIODICALLY  INSPECTING  THE  PRODUCTS  FOR  ADJUSTMENT,  WEAR  AND 
DAMAGE.  THEREFORE,  YOU  MUST  READ  AND  UNDERSTAND  ALL  OF  THE  INSTRUCTIONS  AND  PRECAUTIONS  SUPPLIED  WITH  YOUR  FRONT  RUNNER  PRODUCT  PRIOR  TO 
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY 
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.

Please call us if you have any questions about the installation of this product.

front runner

Содержание SLIMLINE II TRAY


















Отзывы: