manualshive.com logo in svg

Front Runner KRTT001T, Руководство пользователя, Страница: 4 / 5

Поделиться
Скачать
Front Runner KRTT001T Скачать руководство пользователя страница 4

4

3

Before fitting the Wind Deflector, and with
the Rack in the upside down position,
(Check with product sticker. It should be
upside down), slide a M8x16 Hex Bolt into
each end of the First Slat using the
machined slot as shown.

FIT THE RACK

(

)

 A 

Note: If your Slimline II Tray is not already assembled, assemble it as per the Slimline II Tray Universal
Assembly Instruction (Document RRSTUNI). Read Step 3A before fitting the Wind Deflector

REV_A01

(

)

 D 

Place the Side Rails onto the vehicle
lining up the holes in the base of the Side
Rails with the Aluminium Spacers . There
is a left and a right hand Side Rail. The
product sticker must go to the front   
outer side of the vehicle.

Hand tighten the Side Rails to the roof
using the M8x35 Hex Bolts and M8x19x2
Flat Washers Supplied.    

Measure the distance from the top of the
windscreen to the first hole in each rail.
Ensuring that the left and right hand
sides are of equal distance. Fasten all the
bolts.

FIT the SIDE RAILS   

Содержание KRTT001T






Отзывы:

Нет отзывов