Fronius TransSteel 2700c Скачать руководство пользователя страница 69

Страница: 69 / 120

MIG/MAG welding

Safety

WARNING!

Operating the equipment incorrectly can cause serious injury and damage.

▶

Do not use the functions described here until you have read and completely under-
stood these Operating Instructions.

▶

Do not use the functions described here until you have fully read and understood all
of the Operating Instructions for the system components, in particular the safety
rules.

WARNING!

An electric shock can be fatal.

If the power source is connected to the mains electricity supply during installation, there
is a high risk of very serious injury and damage.

▶

Before carrying out any work on the device make sure that the power source mains
switch is in the "O" position

▶

Before carrying out any work on the device make sure that the power source is
unplugged from the mains

Overview

MIG/MAG welding is composed of the following sections:
-

MIG/MAG standard synergic welding

MIG/MAG standard manual welding

Содержание TransSteel 2700c

























































































































Результаты поиска

Содержание TransSteel 2700c

Отзывы:

Похожие инструкции для TransSteel 2700c

Бренды по названию

Популярные бренды

Fronius TransSteel 2700c, Руководство по эксплуатации

Результаты поиска

Содержание TransSteel 2700c

Отзывы:

Похожие инструкции для TransSteel 2700c

Бренды по названию

Популярные бренды