Fronius 4,044,008 Скачать руководство пользователя страница 19

Страница: 19 / 136

Torch body coupling

The torch body coupling enables the
torch body to be changed, length of
coupling = 50 mm (1.97 in.)

Robacta TX W torch body

Wire cutter

Contact tip rec-
ommendation

Note on wirefeed-
ing

Compatible sys-
tem components
for the overall
welding system

Only use the torch body changeover system in conjunction with the following system com-
ponents:
-

Any power source from the TS/TPS series

Any Fronius robot wire-feed unit

Robacta hosepacks

Robacta Drive hosepacks

Robacta Drive CMT hosepacks

Robacta Reamer V Easy, Robacta Reamer V

Robacta Reamer aluminium brush head

Robacta TC series

(1)

NOTE!

The locking balls (1) are

intended for dry operation. Do not
lubricate the locking balls.

NOTE!

In conjunction with the torch body changeover system, we recommend

that you use the 'CB' contact tip.

NOTE!

The torch body changeover system can only be used in conjunction with

wirefeeding from the drum coil.

Содержание 4,044,008









































































































































Результаты поиска

Содержание 4,044,008

Отзывы:

Похожие инструкции для 4,044,008

Бренды по названию

Популярные бренды

Fronius 4,044,008, Руководство по эксплуатации

Результаты поиска

Содержание 4,044,008

Отзывы:

Похожие инструкции для 4,044,008

Бренды по названию

Популярные бренды