manualshive.com logo in svg

Froling TX 200, Руководство по эксплуатации

Поделиться
Скачать
Froling TX 200 Скачать руководство пользователя страница 39

Before starting inspection and cleaning work

Activate service mode before starting inspection and cleaning work

❒ In the quick menu activate “Service mode”

➥ The controller follows the shutdown procedure and starts with the cleaning

cycle

➥ After the cleaning cycle the boiler switches to the "Cleaning possible" operating

status

➥ The tipping grate remains in the open position

❒ Turn off the main switch

 

4.2.4 Periodic inspection and cleaning (approx. 1,000 hrs)

For fuels with a low ash content, cleaning and inspection after approx. 1,000 service
hours is usually sufficient (under normal use conditions, approximately every quarter).
For less efficient fuels and fuels with a high ash content (indicated by short emptying
intervals for the ash container), the work should be carried out more frequently
accordingly.
 

WARNING

Inspection and cleaning work with the boiler switched on
Serious injuries from automatic startup of the boiler and severe burns from hot

parts and the flue gas pipe are possible.

Therefore:

❒ Only carry out work on the boiler when the main switch is turned off
❒ Always wear protective gloves when working on the boiler
❒ Only operate the boiler using the handles provided
❒ Follow the procedure below when starting and finishing inspection and

cleaning work

 

 

 

 

Boiler Servicing

4

Inspection and cleaning

Operating Instructions TX 200-250 | B1060217_en

39

Содержание TX 200
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды