Fritsch PULVERISETTE 5 Скачать руководство пользователя страница 36

Страница: 36 / 72

6.4.7 Wet grinding (grinding in a suspension)

DANGER!
Explosion hazard! Ignition hazard!
The device is not explosion-protected. If flammable liq-

uids are used, make sure that the heat developing in

the grinding bowl does not reach the solvent's boiling

point. Program appropriate cooling phases. If the

vapour pressure is too high, vapours may escape and

ignite.
If it can be avoided, we recommend using non-flam-

mable liquids or liquids with a high boiling point. The

boiling point should be above 80 °C and above 100 °C

for a long grinding duration.

During the transition to grinding in suspension, you can add a liquid aux-

iliary agent with high boiling point and low vapour pressure, e.g. water,

white spirits (boiling point 100 - 140°C), or alcohols with a high boiling

point (e.g. isopropanol)
We recommend that you only use so much liquid that the suspension has

the same consistency as motor oil. With this viscosity the best results can

be achieved in most cases.

6.5 Clamping the grinding bowls

6.5.1 Clamping with the "Safe-Lock" (5) tensioning device

Fritsch GmbH confirms that every Safe‐Lock clamping

system has been manufactured and tested to our

internal quality standards. Fritsch GmbH measures the

clamping force of each individual Safe‐Lock clamping

system. The clamping force must be in the range of 11.2

‐ 11.3 kN +/‐ 0.2kN.

Carry out the following checks for every grinding before clamping the

grinding bowls:

Has the rubber disc (6.1) been inserted into the grinding bowl

holder? The rough side should be facing upwards!

Check the rubber disc in the grinding bowl holder for damage:
Replace the rubber disc if it has been pressed flat!

The Teflon flat seal (for the sealing between lid and bowl) may not be

damaged or soiled.
Replace heavily deformed Teflon flat seals.

Using the device

- 36 -

Содержание PULVERISETTE 5









































































Результаты поиска

Содержание PULVERISETTE 5

Отзывы:

Похожие инструкции для PULVERISETTE 5

Бренды по названию

Популярные бренды

Fritsch PULVERISETTE 5, Руководство по эксплуатации

Результаты поиска

Содержание PULVERISETTE 5

Отзывы:

Похожие инструкции для PULVERISETTE 5

Бренды по названию

Популярные бренды