Fristam Pumps FP Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 32

Fristam Pumps FP Series Скачать руководство пользователя страница 21

Fristam FP/FPX Series Pump

21

Figure 1

S

PARE

P

ARTS

Use of replacement parts that are not approved by Fristam Pump can lead to serious personal injury and
material damage. If you have any questions regarding approved replacement parts, please contact Fristam.

T

RANSPORTATION

Transportation may only be performed by trained personnel.  The pump may be moved using approved
lifting devices suitable for the weight/size of the pump.  Improper securing the pump may result in injury
from falling, tipping, or unsecured parts.  Dimensional information is available for download at www.
fristam.com/usa. Weight information is based on motor selection, and is available upon request.

N

OISE

R

EDUCTION

Operating the pump within its intended design range will aid in reducing the noise to acceptable levels.
•  Avoid excessively low or very high flow rates.
•  Avoid cavitation of the pump.
•  Maintain good piping practices (see below).

I

NSTALLATION

U

NPACkING

Check the contents and all wrapping when unpacking the pump. Inspect the pump carefully for any dam-
age that may have occurred during shipping. Immediately report any damage to the carrier. Remove the
shaft guard and rotate the pump shaft by hand to make sure the impeller rotates freely. Keep the protective
caps over the pump inlet and outlet in place until you are ready to install the pump.

I

NSTALLING

Prior to actually installing the pump, ensure that:

• the pump will be readily accessible for maintenance, inspection and cleaning.
•

adequate ventilation is provided for motor cooling.

•

the drive and motor type is suitable for the environment where it is to be
operated. Pumps intended for use in hazardous environments e.g., explosive,
corrosive, etc., must use a motor and drive with the appropriate enclosure
characteristics. Failure to use an appropriate motor type may result in seri-
ous damage and/or injury.

P

IPING

G

UIDELINES

This section describes good piping practices to obtain maximum efficiency and
service life from your pump.

Maximum performance and trouble-free operation
require adherence to good piping practices.

• Ensuring proper piping support and align-

ment at both the suction inlet and discharge
outlet can help prevent serious damage to
the pump housing (

Figure 1

).

• Avoid abrupt transitions in the piping system (

Figure 2

).

Figure 2

«
...
19
20
21
22
23
...
»

Содержание FP Series

































Отзывы:

Нет отзывов