Fristam Pumps FP Series Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 32

Fristam Pumps FP Series Скачать руководство пользователя страница 2

Fristam FP/FPX Series Pump
2

!

CAUTION:

Begin all pump maintenance operations by disconnecting the

energy source to the pump. Observe all lock out/tag out proce-

dures as outlined by ANSI Z244.1-1982 and OSHA 1910.147

to prevent accidental start-up and injury.

D

ESCRIPTION

This manual contains installation, operation, assembly, disassembly and repair instructions for the
Fristam FP and FPX centrifugal pumps.
The heavy-duty FP pump is flange mounted on a cast flange support. This flange support provides an
extremely sturdy method of coupling the pump head and the motor. It absorbs vibrations and noise.
The flange support also fastens the pump to the floor (or adjustable base). The FP series is available
with either a single or double mechanical seal.
The general purpose FPX pump is mounted on a close coupled-style flange support. The FPX series is
only available with a single mechanical seal.
There are two general styles of pump heads in “F” type Fristam pumps. The 700 and 1700 series
are non-volute style pumps. The 1050, 1150, 3400, and 3500 series are volute style. In general,
maintenance procedures for both series are the same. Any variations will be clearly noted.
The motors used on both the FP and FPX style pumps are standard NEMA totally enclosed fan cooled
(TEFC) motors. They are C-face (except 320TSD, which are D flange - only available on FP series
pumps). Replacement motors are readily available from local motor distributors.

S

AFETY

This instruction and maintenance manual shall be read and completely understood prior
to operation of the pump. The manual should be kept available at the pump installation
location.

All applicable local/national regulation and laws shall be followed.

All work described herein may only be performed by qualified personnel.

Personal protective equipment (PPE) such as hearing protection may be required.

Despite inherent safe design measures some amount residual risk will remain. Throughout
the manual these risks will be pointed out.

«
1
2
3
4
...
»

Содержание FP Series

































Отзывы:

Нет отзывов