background image

8.  The site must allow for the easy 

removal of the connector pipe and 

drain hose.

9.  The unit must be installed at a site 

protected from direct sunlight.

Precautions for Installation

Installation at the following sites may cause problems. If you must inevitably install 

2.   Sites with a high concentration of salinity, such as coastal areas.
3.   Sites with sulfuric gas, such as hot water springs.
4.   Sites with high frequency equipment, such as wireless equipment, welding 

machines and medical installations.

5.   Sites with flammable gases or volatile material.
6.   Sites with special environmental conditions.
7.   Laundry rooms.

Indoor Unit

1.  The unit must be installed at a site 

that does not obstruct the flow of 

air.

2.  The site must support the weight of 

the indoor unit.

3.  The site must be easily accessible 

for maintenance and replacement 

of the air filter.

4.  The site must allow for the 

necessary space around the indoor 

figure.

that the unit be installed at the 

flammable gases.

Choosing the installation site

More

More

More

More

Choosing the installation site

the unit at one of these sites, please consult your local distributor beforehand:

1.   Sites with machine oil.

unit, as shown in the sideward 

meter) between the unit and radio 

5.  There should be at least 3 feet (1 

7.  The indoor unit must be at least 7.5 

feet (2.3 meters) from the ground.

6.  It must be far from fire, smoke or 

center.

or television devices. It is ideal 

than 6"

than 5"

than 7.5'

than 5"

Installation warnings:

Installation

1.   Carefully read the installation manual before beginning.
2.   Follow each step as shown.
3.   Observe all local, state, and national electrical codes and by qualified, 
      licensed, authorized personnel only.
4.   Pay attention to danger and safety notices

07

Содержание FRS093LS1
























Отзывы: