background image

GAS WALL OVEN INSTALLATION INSTRUCTIONS

1

INSTALLATION AND SERVICE MUST BE PERFORMED BY

A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal injury or death.

FOR YOUR SAFETY:
— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor's phone.  Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

— Installation and service must be performed by a qualified installer, service agency or the gas supplier.

NOTE: Wiring diagrams for these appliances are enclosed in this booklet.

P/N 318201554 (0503) Rev. A

English – pages 1-8

Español – páginas 9-16

Wiring Diagram - pages  17-20

Figure 1

Additional Safeguards

• Do not install wall oven beneath the work counter.
• The flue charge shall not be located below the 36" level.

Clearance for complete door opening:

• For model with 2 cavities allow at least 17 5/8".
• For model with 1½ cavity allow at least 19 3/8".

Model with 2 oven cavities

Model with 1½ oven cavity

H

38 

7

/

16

"

37 

3

/

8

"

23 

3

/

8

"

F

G

27"

18"

A

B

C

D

E

Drill a 1½" diameter hole

for gas hook up

Electrical Outlet

Location for model

with 1½ oven

cavity

Electrical Outlet

Location for

model with 2

oven cavities

23 

17

/

32

"

42 

3

/

8

"

21"

19 

3

/

8

"

41 

13

/

16

"

23 

7

/

8

"

25 

3

/

8

"

22 

5

/

16

"

MODEL

CABINET DIMENSIONS

CUTOUT DIMENSIONS

A

B

C

D

E

F

G

H

Model with 2 cavities

19 ½" Min.

2 ½" Min.

24" Min.

16 ¾"

1

/

8

"

22 ½"

24" Min.

42 

1

/

8

"

Model  with 1 ½ cavity

10" Min.

27 ½" Max.

1 ½" Min.

24" Min.

20"

5

/

8

"

22"

23 ½" Min.

37 ½" Min.

39" Max.

Printed in United States

Содержание FGB24T3ESC





















Отзывы: