background image

31

BEFORE CALLING

Concern Potential Cause

Common Solution

Opening/Closing Of Doors/Drawers

Door(s) will 

not close.

•  Door was closed too hard, 

causing other door to open 

slightly.

•  Refrigerator is not level. 

It rocks on the floor when 

moved slightly. 

•  Refrigerator is touching a 

wall or cabinet. 

 

•  Food/packaging is 

obstructing the door from 

closing. 

•  Flipper mullion on left fresh 

food door is not in the 

correct position.

•  Close both doors gently. 

 

•  Ensure floor is level and solid, and can 

adequately support the refrigerator. 

Contact a carpenter to correct a sagging 

or sloping floor.

•  Ensure floor is level and solid, and can 

adequately support the refrigerator. 

Contact a carpenter to correct a sagging 

or sloping floor.

•  Make sure there is no food/packaging 

blocking the doorway.  

•  Ensure the flipper mullion is in the 

correct position to allow the door to 

close. (See Flipper Mullion section.) 

Drawers are 

difficult to 

move.

•  Food is touching shelf on 

top of drawer.

•  Track that drawers slide on 

is dirty.

•  Remove top layer of items in drawer. 

•  Ensure drawer is properly installed on 

track.

•  Clean drawer, rollers, and track. See 

Care & Cleaning.

Running of Refrigerator

Compressor 

does not run.

•  Refrigerator is in defrost 

cycle. 

•  Plug at electrical outlet is 

disconnected.

•  House fuse blown or 

tripped circuit breaker.

•  Power outage.

•  This is normal for a fully automatic 

defrost refrigerator. The defrost cycle 

occurs periodically, lasting about 30 

minutes.

•  Ensure plug is tightly pushed into outlet. 

•  Check/replace fuse with a 15 amp time-

delay fuse. Reset circuit breaker.

•  Check house lights. Call local electric 

company.

Refrigerator 

seems to run 

too much or 

too long.

•  The variable speed 

compressor is designed 

to run 100% of the time 

except during the defrost 

cycle. At times it will run 

faster, such as after a 

defrost cycle.

•  It is normal for the compressor to run 

continuously except during defrost 

mode.

Digital Temperature Setting Display

Digital 

temperature 

displays an 

error.

•  Electronic control system 

has detected a performance 

problem.

•  Contact Electrolux Customer Care for 

assistance with any errors or codes 

flashing in the display by calling 

 

1-800-374-4432.

Содержание FG4H2272UF


































Отзывы: